Factors affecting high commercial losses, Electrical Engineering

Assignment Help:

Factors Affecting High Commercial Losses

Commercial losses in our country occur mainly because of the following reasons:

  1. Incorrect assessment of the energy consumed;
  2. Pilferage of energy; and
  3. Human errors.

You might be wondering: How could these losses are overcome? For this, you need to know the factors that contribute to these losses.

Factors Contributing to High Commercial Losses

1. Theft/pilferage of power through existing consumers.

2. Illegal connection from distribution line by non-customers.

3. Incorrect estimation of energy consumption in respect of un-metered connections.

4. Defective metering.

5. Meter reading errors.

6. Tardy billing and poor revenue collection.

7. Lack of accountability.


Related Discussions:- Factors affecting high commercial losses

amp circuit , Refer to the op amp circuit shown below. Let R 1 = ...

Refer to the op amp circuit shown below. Let R 1 = 140 k_, R 2 = 10 k_, R 3 = 10 k_, R 4 = 20 k_, RL = 10 k_. Assume the op amp is ideal. Find the equation relating the

Rc coupled amplifier over a single stage, Q. What is the advantage of a two...

Q. What is the advantage of a two-stage overloaded RC coupled amplifier over a single stage one? What are it's uses? It is a frequently encountered configuration. Here, the tra

Calculate efficiency to load at unity power factor, Q. A 300-kVA transforme...

Q. A 300-kVA transformer has a core loss of 1.5 kW and a full-load copper loss of 4.5 kW. (a) Calculate its efficiency corresponding to 25, 50, 75, 100, and 125% loads at unity

Find the efficiency of the transformer, Q. Athree-phase, 600-kVA, 2300:230-...

Q. Athree-phase, 600-kVA, 2300:230-V,Y-Ytrans- former bank has an iron loss of 4400 W and a full- load copper loss of 7600 W. Find the efficiency of the transformer for 70% full lo

Buck boost converter - power supplies , Buck Boost Converter The outpu...

Buck Boost Converter The output  of buck boost  regulator may be  less than  or greater than the  input  voltage. Since  the polarity of output  voltage  is opposite  to that

What are the features used mode 1 in 8255, What are the features used mode ...

What are the features used mode 1 in 8255? Two groups - group A and group B are available for stored data transfer. 1. Each group have one 8-bit data I/O port and one 4-bit

Thyristor terminology , Thyristor  Terminology The followings  terms ...

Thyristor  Terminology The followings  terms are used in SCR  specifications: Latching current : The  latching  current is  the value of on stat e current  required  to mai

Calculate the antenna parameters, For a helical antenna, the half-power bea...

For a helical antenna, the half-power beamwidth and directive gain are given by where C = πD, N = L/S, and S = C tan α,in which α is called the pitch angle, and The

Full wave bridge rectifier circuit , Construct a full wave bridge rectifier...

Construct a full wave bridge rectifier circuit and connect it to the transformer output. What is the Output Voltage and Frequency?

Calculate the mechanical speed of rotar, Calculate the mechanical speed of ...

Calculate the mechanical speed of rotar: An asynchronous machine of 460V, 25hp, 4 poles with rotor wound in Y has the following data (of the side stator): Resistance of the

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd