Differentiate thermoplastic & thermosetting plastic material, Electrical Engineering

Assignment Help:

Classify plastic materials into two categories describe their important properties and give two examples of each.

Plastic materials can be categorized in thermoplastic and thermosetting plastics.

Thermoplastic materials: The properties of such plastic materials do not change considerably when they are melted and after that cooled and solidify. They can be repeatedly dissolved or melted in various solvents. They are additional elastic, less brittle and do not lose elasticity while subjected to prolonged heating. They are less apt to age thermally. Again and again they can be remoulded in any shape after heating. Several of them possess extraordinary high insulating properties and they are water repellent. They are polymers of linear structure that is their molecules are elongated and are like thread. This, kind of structure is soluble, fusible, highly plastic, able of forming thin flexible threads as well as films. Illustrations are Polytetra Flouroethylene (P.T.F.E. or Teflon) and Polyvinyl Chloride (P.V.C.)

Thermosetting Plastic Materials: They undergo huge changes while subjected to high temperatures for rather sometimes. They are called as baked and no longer can melt or be dissolved. They are more brittle, less elastic and lose their elasticity while subjected to prolonged heating. Therefore they cannot be remoulded in various shapes once they are hardened and set. They are used, while insulation is to withstand high temperatures without losing or melting its shape and also mechanical strength. Thermosetting plastic substances are space-polymers and the molecules branch off in different directions throughout polymerisation. Such structure makes them extremely rigid, fusible, poorly soluble, and enable of forming elastic films and threads. Examples are Phenol formaldehyde (i.e. Bakelite), Epoxy resins.


Related Discussions:- Differentiate thermoplastic & thermosetting plastic material

Sid input - serial input output ports , SID  Input Serial input data  ...

SID  Input Serial input data  single  bit can be  accepted through this  pin using RIM  command  discussed in details in chapter8.

Determine the maximum value of the voltage induced in coil, Q. A 10-turn sq...

Q. A 10-turn square coil of side 200 mm is mounted on a cylinder 200 mm in diameter. If the cylinder rotates at 1800 r/min in a uniform 1.2-T field, determine the maximum value of

Define two popular parallel protocol used in embedded system, a. Compare th...

a. Compare the serial protocols, parallel protocols and wireless protocols in terms of formats, speed, performance and security issues. b. Briefly define two popular parallel pr

Transformers, AC Operation of an iron core         ...

AC Operation of an iron core         Hence, if a wattmeter were used to measure the power delivered over a full period of the waveform (which will also b

What do you eman by digital circuits, Q. What do you eman by Digital Circui...

Q. What do you eman by Digital Circuits? The use of nonlinear devices (BJT and FET) in constructing linear amplifiers. Although these devices are inherently nonlinear, their op

Explain signal description of 8085, Explain signal description of 8085 ...

Explain signal description of 8085 a) Address bus b) Control and status signal c)  Address latch enable d)  S1,S0 status signals e)  Read ,write signal

Determine the self inductance of the two coils, Determine the self inductan...

Determine the self inductance of the two coils: Two coils with a coefficient of coupling of 0.6 between them are connected in series so as to magnetize (i) in the same directi

Show step-motor control system, Q. Show Step-motor control system? Figu...

Q. Show Step-motor control system? Figure illustrates a system in which the prime mover used in the disk-drive system is a step motor driven by pulse commands. In response to e

Show voltage wave form of rlc series circuit, Q. The voltage wave form of F...

Q. The voltage wave form of Figure is applied to an RLC series circuit with R = 2, L = 2H, and C = 1 F. Obtain i(t) in the series circuit. (Note that the capacitor and inductor va

Transistors, What is the difference between a hybrid pi and an re model?

What is the difference between a hybrid pi and an re model?

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd