User Account

All Pages

assigment.., Mechanical Engineering

Assignment Help:
Describe the internal structure, bonding of atoms and molecules and to understand the mechanical properties of materials.
Comprehensive understanding of properties of materials, atomic bonding of atoms and imperfections. Solution of identification of structures. Writing of an experimental report
Task 1:
One of the major aspect of material science involves the investigation of material structure. The structure of materials has a profound influence on many properties of materials.
Your Task
1. Both Diamond and Graphite are made from carbon. However diamond is considered the hardest material while graphite is brittle and slippery. Explain this difference from atomic bonding view point
2. Inconel is a corrosion resistant, tough Nickel-chromium alloy because it contains large amounts of Nickel & chromium. How does Nickel increases the toughness of the material and chromium protect the metal from corrosion?
3. Industries that manufacture racing cars prefers nickel based alloys for engine components and iron based alloys for structural parts. Justify this statement.
Task 2:
Material engineers should be conversant of various materials, their properties, manufacturing process involved, environmental issues, monetary issues and more.
Your Task
1. Which chromium plating is more eco-friendly - trivalent or Hexavalent? Justify your answer in the light of environmental issues caused.
2. Explain why tempering cycle is essentially required in the heat treatment of high tensile carbon steel and what are the consequences if tempering cycle is not carried out?
3. What are the essential criteria for selecting materials required for the following operating functions?
(a) Turbine blades which endures vibrations and saline conditions
(b) Domestic utensils used in kitchen
(c) Aircraft body to go undetected in radars
(d) Dental braces used in medical field
(e) Rocket Chambers of space shuttles.
Task 3
Ability to write an experimental report in a standard format is a key competency requirement of a Material engineer.
Your Task
1. Write an experimental report with the following aim and objectives details
Aim: The aim of this tensile test is to subject metallic materials to pulling or tensile loading and observe the mechanical behaviour of materials.
Objectives:
a) To note down various loading values applied with corresponding elongations observed and calculate engineering stress and engineering strain values using equations.
b) To plot a curve between engineering stress and engineering strain on a graph sheet and determine the modulus of elasticity of the tested materials.
c) To determine other mechanical properties such as yield strength (sY), ultimate tensile strength (UTS), fracture strength (sf), % of elongation and % of area reduction.
2. Write an experimental report with the following aim and objectives details
Aim: The aim of fatigue test is to develop an understanding on fatigue behaviour of metallic materials and predict fatigue life/stress levels of ferrous and non-ferrous materials.
Objectives:
a) To perform the fatigue test on the given specimens using the Fatigue tester and plot S-N curve
b) To determine the safe fatigue stress levels for the specimens from the S-N curve.

Related Discussions:- assigment..

Determination of reaction at the support beam, Determination of Reaction at...

Determination of Reaction at the Support beam: Draw a SFD & BMD for the beam illustrated in Figure Figure Solution Determination of Reaction at the Support

Determine hydraulic efficiency, A pelton wheel works at the foot of a dam b...

A pelton wheel works at the foot of a dam because of which the head available at the nozzle is 400m. The nozzle diameter is 160mm and the coefficient of velocity is 0.98. The diame

I-Section, An unsymmetrical I-Section as shown in figure below. If maximum ...

An unsymmetrical I-Section as shown in figure below. If maximum bending stress is not extend more than 40MPa in the section than find out the moment which it can bear

Find out also the loss of energy through impact, Find out also the loss of ...

Find out also the loss of energy through impact: Example 1. A bullet weighing 0.1 newton horizontally fired with a velocity of 80 metres/sec hits a wooden block, weighin

Calculate the primary voltage and real power measurements, Question: A ...

Question: A 7.2kVA single phase 50Hz, 480Vrms: 240Vrms transformer can be modelled using the primary referred approximate equivalent circuit shown in Figure 1 below. Fi

Entropy, What is entropy microscopically

What is entropy microscopically

Metal transfer in co2 welding, METAL TRANSFER IN CO2 WELDING In CO 2 wel...

METAL TRANSFER IN CO2 WELDING In CO 2 welding, two distinct types of metal transfers are identified viz. short circuiting transfer and free flight globular transfer. Short Cir

Heat transfer, an elctric current is passed through a wire 1mm in diameter ...

an elctric current is passed through a wire 1mm in diameter and 10mm long. the wire is submerged in liquid water at atmospheric pressure and current is increased until the water bo

Isentropic, isentropic derivation

isentropic derivation

Thermodynamics, Two kg Ammonia (mA) at PA = 300 kPa and TA = -10ºC and 1 kg...

Two kg Ammonia (mA) at PA = 300 kPa and TA = -10ºC and 1 kg Ammonia (mB) at PB = 300 kPa and TB = 100ºC are mixed in a constant pressure and adiabatic process. Find the following:

Write Your Message!

Captcha
Order Assignment

Featured Services

Order Now

Popular Subjects

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +91-977-207-8620

Phone: +91-977-207-8620

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd