Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
You are working in a company that has developed a process to produce DNA vaccines from E.coli. After the fermentation step a lysis step is used to release the DNA from the cells resulting in a sticky mixture. You find that an aggressive cleaning solution heated to 80°C is required to clean the sticky mixture off the inside of the lysis tank. A counter-current shell-and-tube heat exchanger containing 100 tubes is used to heat the cleaning solution from 10°C to 80°C at a mass flow rate of 8.6 kg s-1. The tubes have external and internal diameters of 11 and 10mm, respectively, and a thermal conductivity of 17 W m-1 K-1. Water enters the shell at 90°C at a mass flow rate of 22 kg s-1. The shell side heat transfer coefficient is 2500 W m-2 K-1.
You are given the following data:
The following correlation applies for turbulent flow in pipes: Nu = 0.023 Re0.8Pr0.4
Cleaning Solution: Thermal conductivity = 0.5 W m-1K-1 Viscosity = 1 x 10-3 Pa s Specific heat capacity = 3.68 kJ kg-1 K-1 Density = 1,100 kg m-3
Water Specific heat capacity = 4.18 kJ kg-1 K-1
a) Calculate the surface area available inside the heat exchanger.
b) You notice that with time the aggressive cleaning solution causes corrosion in the heat exchanger resulting in a build up of layers of rust deposits. If you were to buy a new heat exchanger, suggest ways you could re-specify its design so as to limit the damage by corrosion?
determine the average applied force exerted on to the pile hammer. Note because the force is applied over a short time period it can be considered as an impulse force.
a brayton cycle gas turbine delivers power to an electric generator at 150 mw. the minimum nbsptemperature in the cycle
if the bar has clockwise angular velocity of 10 rad/s and Va= 20m/s what are coordinates of instantaneous center of the bar, and what is the value of Vb?
a simple pulley with the given radius r used to lift heavy objects is positioned 10 feet above ground level. Given that the pulley rotates theta degrees, determine the height to which the pulley is lifted.
Calculate the adiabatic flame temperature (at constant pressure) for ethane C2H6 in air
A 0.4 W cylindrical electronic component with a diameter of 0.3 cm and length 1.8 cm is mounted horizontally on a circuit board. To cool the component air is flowing across the board at a velocity of 150 m/min. If the air temperature is T∞= 45°C, ..
A glass/epoxy laminate with a fiber orientation of 30 degrees is subjected to a shear stress t_xy (or tau_xy) which can be positive or negative.
Air enters a turbine at 40 kN/m2, 900 C, and leaves at 10 kN/m2. The flow is reversible and adiabatic. Inlet velocity is quite low and outlet velocity is 150 m/s through a cross-sectional area of 0.20 m2. Calculate the power output in kW.
No heat interactions with the environment are allowed. You do not need to describe the details of the process that produces the maximum work, but you do need to describe the final state of the blocks fully.
A long electric wire of radius r0 generates heat at rate of q'''. The surface is maintained at uniform temp of T0. Write heat equation and boundary conditions for steady state one dimensional conduction.
a dump truck is shown in the figure. the loaded container has a mass of 8000 kg and may be modelled as a solid
a package is dropped from the plane which is flying with a constant horizontal velocity of va150fts. determine the
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd