Write the differential equation and identify the boundary

Assignment Help Mechanical Engineering
Reference no: EM13623854

Consider a one-dimensional plane wall of thickness 2L. The surface at x = -L is subjected to convective conditions characterized by T_infinity1, h1, while the surface at x = +L is subjected to conditions T_infinity2, h2. The initial temperature of the wall is T0 = (T_infinity1 + T_infinity2) / 2 where T_infinity1 > T_infinity2. (a) Write the differential equation, and identify the boundary and initial conditions that could be used to determine the temp distribution T(x,t) as a function of position and time. (b) On T-x coordinates, sketch the temp distributions for the initial condition, the steady-state condition, and for two intermediate times for the case h1=h2.

Reference no: EM13623854

Questions Cloud

Describe schematically the equipotential surfaces : describe schematically the equipotential surfaces corresponding toa a constant electric field in the z-directionb a
05002 m along the datum line 04999 m and 05001 m along : deformation measurements were made on a flat rock surface using 0.5000 m-long gauge lengths. the following observations
Of a random sample of 90 firms with employee stock : of a random sample of 90 firms with employee stock ownership plans 40 indicated that the primary reason for setting up
Determine the capacitance of the system and the potential : a cylindrical capacitor has two co-axial cylinders of length 15 cm and radii 1.5 cm and 1.4 cm. the outer cylinder is
Write the differential equation and identify the boundary : consider a one-dimensional plane wall of thickness 2l. the surface at x -l is subjected to convective conditions
Captain ds tuna is sold in cans that have a net weight of 8 : captain ds tuna is sold in cans that have a net weight of 8 ounces. the weights are normally distributed with a mean of
An inductor with an inductance of 290h and a resistor with : an inductor with an inductance of 2.90h and a resistor with a resistance of 6.00 ohms are connected to the terminals of
Discuss five of the ten major benefits of strategic : discuss five of the ten major benefits of strategic management as stated by greenley. which of these benefits do you
The record low sea-level barometric pressure ever recorded : the record low sea-level barometric pressure ever recorded is 25.8 in. of mercury. at what altitude in the standard

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  You are to supply a design for an engine room crane

You are to supply a design for an engine room crane which will provide maintenance support for the main engine. Your design should include the rails the crane will sit on.

  A train made up of 3 cars of weight 60000 lb each connected

a train made up of 3 cars of weight 60000 lb each connected by coupling springs of stiffness 15000 lbin. is released by

  If the density of the aniline is 1002 kgm cube and the

a centrifuge bowl with 250mm internal diameter is turning at 4000 rmin. it contains a layer of aniline 50mm thick. if

  The system undergoes a polytropic process resulting in the

a closed system contains 0.8 kg of air initially at 155 kpa with a volume of 0.45 m3. the system undergoes a polytropic

  Assume the brake pads are 1 lbmin with a heat capacity of

a car with mass 3250 lbm is driven at 60 mih when the brakes are applied to quickly decrease its speed to 20 mih.

  Assuming to 300 k and a 2 x 10-5 m estimate the pressure

an ideal gas of molar mass m is located in a uniform gravitational field whose free fall acceleration is g. a find the

  We''re asked to determine the deflection of a beam location

We're asked to determine the deflection of a beam location for a 2000N load. However the force is directed up the corner NOT centroid.

  If solar radiation is incident on the spacecraft at a rate

would a flagpole made of steel or aluminum freeze ones tongue to it faster? why? thermal conductivity 2. the outer

  Determine the critical crack length for an internal crack

determine the critical crack length for an internal crack in a thick 2024-t6 alloy plate that has a racture toughness

  Find max specific range and max range airspeed

Find Max Level Airspeed at 95% RPM and find Max Range Airspeed (VBR) and Max Endurance Airspeed (VBE) - find Max Specific Range and Max Range Airspeed

  At the diffuser exit the temperature is 430 k determine the

air enters an insulated diffuser at 260 k and 60 kpa with a velocity of 633.9 ms. at the diffuser exit the temperature

  At what speed must they pass through the furnace to be at

steel rods of 0.05m diameter are heat treated by being passed through a heat-treating furnace in which the atmosphere

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd