Write an appraisal of mathcad including a comparison

Assignment Help Mechanical Engineering
Reference no: EM13216755

write an appraisal of mathcad including a comparison with mathlab. describe another feature of mathcad, giving examples of how it can be used.

Reference no: EM13216755

Questions Cloud

Design a container using differentiation : design a container using differentiation that has a volume of 2500 litres. it must use the minimum amount of material.
How many engagement points on the flywheel : a full revolution has 100 rpm flywheel rotation. the press is equipped with two hand palm buttons mounted on the machine at a distance of 20 inches from the point of operation. How many engagement points on the flywheel would be necessary to make ..
Experiment to test whether alcohol consumption : Design an experiment to test whether alcohol consumption influence people's tendency to become socially agressive.
Determine the automobiles braking distance : If an automobile's braking distance from 100 km/h is 60 m on level pavement, determine the automobile's braking distance from 100 km/h when it is (a) going up a 60 incline, (b) going down a 2-percent incline.
Write an appraisal of mathcad including a comparison : write an appraisal of mathcad including a comparison with mathlab. describe another feature of mathcad, giving examples of how it can be used.
Securing a warrant or the employer’s permission : Explain circumstances where OSHA is allowed enter and inspect a worksite without securing a warrant or the employer’s permission.
Find the exit velocity of the neon : A turbine takes in 2 kg/s neon at 27C and 200 kPa with negligible velocity. The produced work is 75 kW and 30 kW of heat leaks into the turbine from the surroundings. The neon exits at 100 kPa and 230 K. Find the exit velocity of the neon.
Characteristic of chaebols for both local and global economy : Identify the positive and negative characteristics of chaebols for both local and global economy. Also, explain the role they play in the South Korean economy.
What is effect of modeling a plane stress as plane strain : IN FE analysis, What is effect of modeling a plane stress as plane strain and vice a versa?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the largest allowable square cross

Determine the largest allowable square cross section of a steel shaft of length 6 m if the maximum shearing stress is not to exceed 135 MPa

  Brick cube is then placed in ambient temperature conditions

A fireclay brick cube, 10 cm in length is removed from a furnace where it was maintained at a temperature of 500 degrees C. The brick cube is then placed in ambient temperature conditions.

  Determine the angle theta degrees

However, even when the cylinder is pressurized, the torque T is still sufficient to keep the seam closed so that no water leaks out. Determine the angle theta degrees that requires the minimum torque T to keep the seam closed. (Hint: use Mohr's ci..

  Determine the heat flux and the temperature gradient

consider a plane wall 100mm thick and of thermal conductivity 100 w/m .k seady state conditions are known to exist with T1 = 400 k T2= 600 K. determine the heat flux and the temperature gradient off the coordinate systems.

  Determination of the heat transfer coefficient values

this would provide you with a set of Reynolds numbers. Next, using the integral method, determine the velocity profiles within the boundary layer to be followed by determination of the heat transfer coefficient values for your selected Reynolds numbe..

  Calculate the mass of steam in the vessel

A rigid vessel of capacity 0.6 m3 contains dry saturated steam at 4.0 bar. The vessel is cooled until the pressure is reduced to 2.0 bar, Calculate; a) the mass of steam in the vessel.

  Construct the homogeneous solution

Construct the homogeneous solution in terms of four constant that could be determined from initial conditions and show the equations of motion

  Calculate the heat transfer and the work done

Saturated water vapor at 200oC is isothermally condensed to a saturated liquid in a piston-cylinder device. Calculate the heat transfer and the work done during this process in kJ/kg.

  Determine the outlet temperature and pressure drop of air

Air at 200 kPa enters a 2-m-Iong, thin-walled tube of 25-mm diameter at 150°C and 6 m/s Steam at 20 bars condenses on the outer surface.

  Explain compressive stress

Important information about Compressive Stress, A circular cross sectional bar with a diameter of 3.25 inches is loaded with a uniform axial compressive load of 22,750 pounds. What is the compressive stress along a cross section of the bar?

  Explain working with boiler suspension bolts

Working with boiler suspension bolts. An HRT boiler is 4766mm long and 3533mm in diameter. It has 66 steel tubes with a diameter of 9mm. The total dry weight of the boiler is 2.565 tonnes

  Find the needed length of the heated section

Find the needed length of the heated section of the tube and find the temperature of the water when it exits the heated section of the tube.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd