Write a function that initializes the interface

Assignment Help Mechanical Engineering
Reference no: EM131090152

Interface an 8-bit serial device using SPI. The control pin is interfaced to PT2, and the clock and data signals are connected to the SPI. The control and clock signals are normally high. The SPI needs to clock data out on the falling edge of the clock. The clock and data are created by the real SPI, and the control signal is bit-banged. The maximum clock frequency is 1 MHz.

a) Write a function that initializes the interface.

b) Write a function that outputs (transmits) one byte using the SPI port. First send eight bits of data, then make PT2 low, then make PT2 high again.

Reference no: EM131090152

Questions Cloud

Change in mean total cholesterol : What is the power of this study to detect a change in mean total cholesterol from 190 to 165 mg/dL with a sample size of 20 people on each diet with 95% confidence? Based on earlier experience, the standard deviation of total cholesterol in the po..
How close does site come to providing full pert diagrams : Visit the Project Library (Links to an external site.) and review the documents concerning Costs and Funding. How do current cost estimates compare with initial cost estimates? Does this match the material your authors provide on project crashing?..
Proportion of women have total serum cholesterol : The mean total serum cholesterol level in women free of cardiovascular doses is 205 with a standard deviation of 19.2. What proportion of women have total serum cholesterol levels exceeding 200?
Identify whether the research is qualitative or quantitative : Review 6 or more contemporary, research-based articles of interest that relate to your chosen topical area or function and area of prospective practice. Summarize the problems that the research articles are addressing. Identify whether the researc..
Write a function that initializes the interface : Write a function that initializes the interface.
Define any private global variables you need : Define any private global variables you need.
A history of intolerance in america : 1. Find at least 5 points of comparison between the textbook and the articles you have selected. This means that you should find five things we have talked about from the text book and show how the articles demonstrate each of those 5 things (usin..
Filling cans of carbonated beverage : The fill volume of an automated filling machine used for filling cans of carbonated beverage is normally distributed with a mean of 12.4 fluid ounces and a standard deviation of 0.1 fluid ounce.
What cpha cpol mode should you use : What CPHA, CPOL mode should you use?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd