With the piston face resting against the stops the water

Assignment Help Mechanical Engineering
Reference no: EM13625936

A piston-cylinder assembly is fitted with stops. The assembly contains 0.1 kg of water, initially at 1 MPa and 500°C. The water undergoes two processes in series:

Process 1-2:

Constant-pressure cooling until the piston face rests against the stops, at which point the volume occupied by the water is one-half of its initial volume.

Process 2-3:With the piston face resting against the stops, the water cools to 25°C.

(a) Sketch the two processes in series on a P-v diagram.

(b) Neglecting kinetic and potential energy effects, evaluate the work and heat transfer for each process (each in kJ).

Reference no: EM13625936

Questions Cloud

A three-blade helicopter blade rotates at 200 rpm if each : a three-blade helicopter blade rotates at 200 rpm. if each blade is 12 ft long and 1.5 ft wide estimate the torque
Successive maximum displacements of a spring-mass-dashpot : successive maximum displacements of a spring-mass-dashpot system shown by fig. 19.10 of vector mechanics for engineers
The drag characteristics of an airplane are to be : the drag characteristics of an airplane are to be determined by model tests in a wind tunnel operated at an absolute
A steam pipe is covered with 150 cm thick insulating : a steam pipe is covered with 1.50 cm thick insulating material of thermal conductivity .2000 calcm degress c s. how
With the piston face resting against the stops the water : a piston-cylinder assembly is fitted with stops. the assembly contains 0.1 kg of water initially at 1 mpa and 500degc.
If the frequency is variable and the length of the closed : 1. if the frequency is variable and the length of the closed at both ends tube is fixed at 45 cm sketch the plastic
Determine the average normal stress at the section a-a and : determine the average normal stress at the section a-a and the average shear stress at section b-b in member ab. the
A piston-cylinder contains 08 kg of nitrogen initially at : a piston-cylinder contains 0.8 kg of nitrogen initially at 100 kpa and 27 degrees. the nitrogen is compressed slowly in
A professional diver performs a dive from a platform 10 m : a professional diver performs a dive from a platform 10 m above the water surface. estimate the order of magnitude of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A closed system contains 2-kg of air undergoes an

a closed system contains 2-kg of air undergoes an isothermal process from 600 kpa and 200oc to 80 kpa. determine the

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Determine the percent increase in the velocity of air

If the density of air is 1.20 kg/m^3 at the inlet and 1.05 kg/m^3 at the exit, determine the percent increase in the velocity of air as it flows through the dryer.

  Calculate the pressure drop

The total hot water flow rate is 10 gal/min which is equally divided among 16 plates. The average temperature of hot water is 80C. Calculate the pressure drop.

  Draw a t-s diagram of the process through the cycle neglect

a gas refrigeration system composed of a turbine a compressor and two heat exchangers is operating at steady state. air

  Determine symbolic expression for total thermal resistance

Determine a symbolic expression for the total thermal resistance of wall, including inside and outside convection effects for prescribed conditions.

  Refrigerant-134a enters the evaporator coils placed at the

refrigerant-134a enters the evaporator coils placed at the back of the freezer section of a household refrigerator at

  Determine the number of revolutions

Determine the number of revolutions that the motor executes in a) reaching its rated speed, b) coasting to rest.

  If the density of the aniline is 1002 kgm cube and the

a centrifuge bowl with 250mm internal diameter is turning at 4000 rmin. it contains a layer of aniline 50mm thick. if

  Heat is added at constant pressure until a temperature of

a cold-air standard diesel cycle has a compression ratio of 16 and begins compressing air isentropically from an

  The elongation of the rod is 2mm and its diameter becomes

a solid circular rod is 800mm long with a radius of 15mm is subjected to an axial force of p80kn. the elongation of the

  Problem 1 air at 295ordmc db flows over a cooling coil and

problem 1 air at 29.5ordmc db flows over a cooling coil and leaves it at a state of 13ordmc db and 8.5 gkg absolute

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd