Wide range of environmental conditions

Assignment Help Mechanical Engineering
Reference no: EM13886266

Humans are able to control their heat production rate and heat loss rate to maintain a nearly constant core temperature of under a wide range of environmental conditions. This process is called Thermoregulation. From the perspective of calculating heat transfer between a human body and its surrounding, we focus on a layer of skin and fat, with its outer surface exposed to the environment and its inner surface at a temperature slightly less than the core temperature, . Consider a person with a skin/fat layer of thickness and effective thermal conductivity . The person has a surface area and is dressed in a bathing suit. The emissivity of the skin is .
When the person is in still air at and the convection heat transfer to the air is characterized by a free convection coefficient of ,
a) Express the energy balance at the skin surface in function of the heat transfer three modes
b) Determine an equation for the skin surface temperature
c) By linearizing the radiation term by , evaluate the skin surface temperature for
d) Determine the rate of heat loss to the environment
e) Repeat parts c) and d) without linearization
When the person is in water at , what is the skin surface temperature and heat loss rate? Heat transfer to the water. Note that liquid water is opaque to thermal radiation and heat loss from the skin surface is only by convection with a convection coefficient

Reference no: EM13886266

Questions Cloud

Determine posterior predictive probability and extreme value : Determine the posterior predictive probability P(y > .5/ y1,.... , y120) (the probability of a dangerous mercury level) and also the extreme value P(y > 3.0/y1, . . . , y120).
What speed should be selected for a wind tunnel model : A proposed model study of a low-speed aircraft is to be performed using a 1:10 scale model. If the prototype is to travel at 25 m=s, what speed should be selected for a wind tunnel model? Is such a test advisable?
Required input power of the pump : For a discharge of Q ¼ 100 L=min and a loss across the pump of hL ¼ 7 m, what is the required input power of the pump if its ef?ciency is 78%?
Identify the consequences of the actions : Consider these three problems. In writing a paper about all three of them individually, identify the consequences of the actions taken, and then determine whether the actions taken represented a greater good, who would benefit from the good, and whet..
Wide range of environmental conditions : Humans are able to control their heat production rate and heat loss rate to maintain a nearly constant core temperature of under a wide range of environmental conditions.
Identify the characteristics of false reports of crime : Demonstrate deductive reasoning and critical thinking skills through application in hypothetical examples of criminal behavior. Identify the characteristics of false reports of crime and staged crime scenes
Determine the effects of the dimples : A model of a golf ball is to be studied to determine the effects of the dimples. A sphere 10 times larger than an actual golf ball is used in the wind tunnel study. What speed should be selected for the model to simulate a prototype speed of 50 m=..
Determining the horizontal rectangular channel : Water from a low dam is released through a sluice gate on a horizontal rectangular channel. The depth of water upstream of the sluice gate is 16.0 m above the channel bed andthe gate opening is 1.5 m.
What mass of o2 should be present : Consider the reaction 2ZnS + 3O2 → 2ZnO + 2SO2. Suppose that you wanted enough O2 to completely react with 500. g of ZnS. What mass of O2 should be present?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the required diameter of a 3 m long stainless

calculate the required diameter of a 3 m long stainless steel annealed rod subjected to an axial tensile load o f 67

  What is the rate of heat loss per meter of pipe

A pipe with OD 6.03cm, ID 4.93cm carries steam at 250deg C with h = 200 W/m^2.K The pipe is covered with 2.5cm of magnesia (85%) insulation followed by 2.5cm of polystyrene (k = .025 W/m.K The outer surface is exposed to air at T = 20 deg C with h = ..

  Determine a the net power developed in kw b the thermal

water is the working fluid in a regenerative rankine cycle. the pressure and temperature at the turbine inlet are 8mpa

  Air flows through the brayton cycle with a mass flow rate

modified brayton cycle is to be analyzed using the air-standard assumption with constant specific heats at a

  What is the effect of water temperature on the pump power

A pump is used to raise the pressure of water from 0 psig to 55 psia. How much power (in kW) will be required to pump 1.5ft3/s of water? What is the effect of the water temperature on the pump power that is required?

  Three wires are made of the following materials one wire

three wires are made of the following materials. one wire is pure al. one wire is pure cu. one wire is pure ni. which

  At the entrance of the air conditioning system determine

atmospheric air at 98 kpa and 30degc flows into an air conditioning system with a volume flow rate of 2 m3min. to

  Determine the initial tension in the cord

The spool has a mass of 75 kg and a radius of gyration . It rests on the inclined surface for which the coefficient of kinetic friction is . If the spool is released from rest and slips at A, determine the initial tension in the cord and the angul..

  How much power does the pumo add to the fluid

Sea water (p=1025 kg/m3) flows through a pump at 0.21 m3/s. The pump inlet is 0.25m in diameter. At the inlet the pressure is -0.15 in of mercury. The pump outlet, 0.152 m in diameter, is 1.8 m above the inlet. The outlet pressure is 175 kPa. If the ..

  A window air conditioner that consumes 1 kw of electricity

a window air conditioner that consumes 1 kw of electricity when running has a coefficient of performance of 3 is placed

  Determine the internal energy change for this process

A tank of CO2 has a volume of 0.15 m^3, contains 0.8 kg of CO2 at a pressure of 453.4 kPa. 10% percent of the mass is removed in such a way that the pressure falls to 371.8 kPa. Determine the internal energy change for this process.

  Determine exergy destroyed and minimum work input process

A well-insulated rigid tank contains 1 kg of air at 30°C. A paddle wheel rotates inside the tank and increases the temperature of the air to 60°C. If the environment is at 100 kPa and 25°C, determine the exergy destroyed and the minimum work input fo..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd