Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Assume that the I bit for external hardware interrupt IRQ is enabled and is low-level triggered. Explain how this interrupt works when it is activated. How can we make sure that a single interrupt is not interpreted as multiple interrupts?
For computer chip of 10mm (length), 10 mm(width) is operated by power of 0.345 watt, which surrounded by coolant material of temp of 70 F. The Internal energy rate is 3.5J/sec and kinetic energy rate is -4.5J/sec.
Three -phase motor is connected to a three-phase power source that has an abc phase sequence. the first load is a wye-connected, three-phase motor withdrawing a line current of 20A at a 0.8 lagging power factor.
MOSFET Amplier Sketch the 4-resistor bias network for an amplier with an n-channel enhancement-mode MOSFET, with R1 = 1Mohm ; R2 = 1:5Mohm ; RD = 75kohm ; Rs = 39kohm ; K = 25microA/V2 ; VDD = 10V and Vto = 1V.
A police K-band radar is operating, with transmit power of 1000 Watts and antenna gain of 300 in linear units. The radar unit is designed to detect a target with a radar cross-section (RCS) of 6 sq. meters and its receiver can detect a signal
1. Find the transfer function 2. Find the Laplace transformation of the output when x(t)=sin(t)u(t) 3.Find the output by taking the inverse Laplace transform of part 2.
A selective-repeat (SR) data link layer protocol uses 4 sequence bits to number it's frames. The source, C starts from frame 0 and proceeds following the Sr protocol. Let us start analyzing the frame/ACK transmissions when the first outstanding fr..
The following functions describe the oscillations in electric circuits and the vibrations of machines and structures. Plot these functions on the same plot. Because they are similar decide how best to plot and label them to avoid confusion.
(a) If five different types of chips are to be placed on the board, how many different layouts are possible (b) If the five chips that are placed on the board are of the same type, how many different layouts are possible
What RF bandwidth is required to send the data using QPSK? If the RRC filters in the transmitter and receiver are replaced with ones that have ? = 0.20, what are the new RF bandwidths in parts (a) and (b)?
If a silicon diffusion is doped with phosphorus (donors) at a concentration of 0.6 x 10^17/cm^3, what is the concentration of holes in this piece of silicon per cm^3 Assume ni = 1.45 x 10^10/cm^3, n = 1000 cm^2/V-s, p = 400 cm^2/V-s
A copper busbar 10cm wide, 5 mm thick, and 10 m long carries a current of 2kA, Calculate the voltage drop if the temperature of the busbar is 120 degree. What is the power loss per meter
A transmission line is specified by the following, while operated at omega w=6*10^8 rad/s, L'= 0.4*10^-6 H/m, C'=40*10^-12 F/m, G'=80*10^-6 S/m, and R'=20 ohms/m. Find the attenuation rate after a wave propagates 10 meters on this line.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd