User Account

All Pages

Why motor rated in kw/horsepower instead of kva

Assignment Help Electrical Engineering
Reference no: EM13665308

Why Motor rated in kW/Horsepower instead of kVA? with examples .

Reference no: EM13665308

Questions Cloud

Decide the current in the rods : Two rigid rods are oriented parallel to each other and to the ground. The rods carry the similar current in the same direction. The length of each rod is 0.90 m, and the mass of each is 0.062 kg. One rod is held in place above the ground, while the o..
Main difference between active and passive : What is The Main Difference between Active and passive Components ?
Decide graphically the characteristics of the image : A tarantula is sitting 4.5 m in front of the concave spherical mirror by radius of R=1.4m. Construct a ray diagram to scale showing the object, image and the mirror. Decide graphically the characteristics of the image.
Observers on the earth gauge for the speed of the laser beam : You are traveling in a spaceship at a speed of 0.56c away from Earth. You send a laser beam toward Earth traveling at velocity relative to you. What do observers on the Earth gauge for the speed of the laser beam?
Why motor rated in kw/horsepower instead of kva : Why Motor rated in kW/Horsepower instead of kVA
Ball allowed to hang straight down motionless : A small ball is attached to one end of a spring that has an unstrained length of 0.188 m. The spring is held with the other end, and the ball is whirled around in a horizontal circle at a speed of 2.91m/s. The spring remains nearly parallel to the gr..
What is the stress on the wire : A robot holds a 20 meter long steel wire of diameter =2 cm that has a load of 25,000 N on it.. How much will the wire stretch under the load? What is the stress on the wire?
Reflected light is minimum-possible thicknesses of film : A thin film of alcohol (n=1.36) lies on a flat glass plate (n=1.51). The film thickness is unknown but is determined by some method to be less than 1000nm.
Describe significance of permeability or ionic concentration : Briefly describe the significance of permeability and ionic concentrations in the process of maintenance of cellular membrane potential.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What are the amplitude-phase and frequency of the signals

For the Current and Voltage equation shown below, What are the amplitude, phase and frequency of the signals. Does Currentlead or lag voltage and by how much is(t) = 57.3 cos (37[rad/sec]t + 37.3o) [A]

  An underwater optical communications system that implements

an underwater optical communications system that implements forward error correction is demonstrated. the system uses a

  Design a second-order butterworth bandpass filter

Design a second-order Butterworth bandpass filter with the following specifications: Bandwidth:400HzCenter frequency: 2000Hz Determine the transfer function and realize it using the Sallen-Key circuit topology.

  Modify counter except for hooking logic to inputs and output

Assume you have a 3-bit pre-packaged counter. You cannot modify thecounter except for hooking logic to the inputs and outputs. Thecircuit has synchronous load and synchronous reset control inputs.The loadable inputs are a2, a1, and a0 (with a2 as ..

  Identify points 10 diffusion lengths from depletion region

Make a dimensioned log (p and n) versus x sketch of both the majority and minority carrier concentrations in the quasineutral regions of the device. Identify points 10 and 20 diffusion lengths from the depletion region edges on your sketch.

  Determine the distribution of the number of customers

Determine the distribution of the number of customers waiting in the queue.

  Determine the output response of an lti system

An LTI system has an impulse response h(t) = e^(t) u(-t),where u(t) is the unit step signal. (a) Give a differential equation description for the system. (b)Suppose that an input signal is given as x(t) = e^(-t) u(t). Determine the output response.

  Find what is the diode current with the load connected

Design a diode voltage regulator to supply 1.5V to a 150-ohm load. Use two diodes specified to have a 0.7-V drop at a current of 10mA. The diodes are to be connected to a +5-V supply through a resistor R.

  Feedback control system can you solve the problems in the

can you solve the problems in the attached file course name feedback control systemdeadline 3182014

  Design to give an output that is one third of supply voltage

Design it to give an output that is 1/3 of the supply voltage. Furthermore, neither the power ratings of the resistors nor the current rating of the supply are to be exceeded. The voltage output of the divider must not change by more than 1% when ..

  When the suspending threads make an angle of 10 degrees

A charge Q is placed on each sphere> the electric force of repulsion separates the spheres, and an equilibrium is reached when the suspending threads make an angle of 10 degrees. Assuming a gravitational force of 9.80(N/kg) and a negligible mass f..

  From which circuit is the recovered modulating signal taken

The FM input to a PLL demodulator has an unmodulated center frequency of 10.7 MHZ. (a) To what frequency must the VCO be set (b) From which circuit is the recovered modulating signal taken

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd