Why do you think we need both rectangular and polar forms

Assignment Help Electrical Engineering
Reference no: EM13250574

(1) Why do you think we need both rectangular and polar forms?

(2) There still seems to be some confusion about the relationship between R, Xc, OR XI and the phase angle. Take a value for R and a value for XC that is ten times smaller than R and find theta, and values will do. Now solve for theta when R and Xc are equal. Finally, make Xc ten times larger than R and find theta. Do the same with R and XL.

Reference no: EM13250574

Questions Cloud

Describe what is the internal function of dynamo : Is it possible to produce a large size dynamo which can satisfy the electricity needs of a home. Is is possible to use the electricity produced by the dynamo to run a motor which can operate dynamo.
Find the direction for the curvature : A stream of protons and electrons are shot horizontally (from the left edge of the page to the right) with a speed of 1.2 x 10^6 m/s, What is the radius of the curvature and the direction for the curvature that each of these particles undergoes
What is the fixed cost of running the x-ray clinic : What would the number of paying patients and federally funded seniors be if the federal funding agency raised its rate to $120 per treatment?
Explain the concentrations of the gases at equilibrium : What are the concentrations of the gases at equilibrium, if the initial concentration of carbon monoxide and water vapor are both equal to 0.325 M. Can you explain me what is the formula and how did you do it
Why do you think we need both rectangular and polar forms : Why do you think we need both rectangular and polar forms. There still seems to be some confusion about the relationship between R, Xc, OR XI and the phase angle. Take a value for R and a value for XC that is ten times smaller than R and find the..
What is the exchange rate today : Suppose that you expected the exchange rate in one year to be 1.2 dollars per euro. What is the exchange rate today?
How much electricity is needed for single rotation of motor : What are the types of motor Which motor is user in Car Engines which is the most efficient motor How much electricity is needed for single rotation of general motor
Compute kc2 for the dimerization : Calculate Kc2 for the following dimerization: 2NO2(g) -> N2O4(g), knowing that Kc = 2.24 for the decomposition written as half N2O4 -> NO2
Explain the sakur-tetrode equation : Calculate so for cooling 1.00 mol of Ne from 298K to 253K under constant volume conditions using the Sakur-Tetrode equation

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Write a program to implement an fir filter

Your program should be efficient in the use of memory and computational complexity.

  Calculate the signal to noise ratio given rms noise voltage

1. Given R = 50Kohm and C = 100nF what is the frequency of oscillation 2. Given a required frequency of oscillation of f = 10kHz and R = 8kohm, what should the value of C be Calculate the signal to noise ratio given RMS Noise Voltage = 20mV and RMS S..

  How a transformer works

How a transformer works and apply those rules to a transformer where the primary core cross-sectional area is twice.

  Determine the velocity of b relative to a

Racecar A is traveling on a straight portion of the track while racecar B is traveling on a circular portion of the track. At the instant shown, the speed of A is increasing at the rate of 10 m/s2, and the speed of B is decreasing at the rate of 6..

  What is the highest power supply in v

Assume you buy a 1 kOhm resistor with +/- 20% tolerance in its value. You would like this resistor to consume at most 2 W of power, otherwise it might burn. What is the highest power supply in V you would use to power it

  Does the higher potential need to be negative or positive

Two charges are held fixed in an x-y plane. Charge Q=-1*10^-9 C is located at the origin, q=3*10^-9 C is located at (0,2). Determine the voltage (v_ba) between point 'b' located at (3,0) and point 'a' located at (1,0).

  What is the maximum amount of transmissions per hour

A mote draws an average of 200mA when "awake", 0.1mA when "sleeping", and 400mA (total) when "transmitting". Transmitting data takes 2ms, and sensor acquisition takes 1ms. If the maximum size battery available is 5000mAh

  What sources to pick to get total absorbed power

what sources to pick to get total absorbed power and total delivered power, since a,e,f, and h absorb and b,c,d,and g supply and for total they suggest a+c+d+e+c=absorbed and b+g+f=delivered

  What is the total number of electrons transported

What is the total number of electrons transported from the positive electrode to the negative electrode by the charge escalator from the time the battery is first used until it is completely dead?

  Sketch the dft

Sketch the DFT(discrete fourier transform)for a square wave with frequency 1Hz and 10 Hz given N=64 and SR(sample rate)=128. Make sure to label your axes.

  Explain difference in registered mode and combinational mode

A GAL is different from a PAL because A GAL has more inputs and outputs; A GAL is implemented with a different technology; A GAL can replace several different PAL's; A GAL can be reprogrammed and a PAL cannot

  Design parallel resonant circuit that capacitor can adjust

Design a parallel resonant circuit so that a variable capacitor can adjust the resonant frequency over the AM broadcast band, 535 to 1605 kHz, with Q

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd