Why are ultraviolet emitting sources avoided

Assignment Help Mechanical Engineering
Reference no: EM131083374

The following questions deal with laser sources in Raman spectroscopy.
6 The following questions deal with laser sources in Raman spectroscopy.

(a) Under what circumstances would a helium-neon laser be preferable to an argon-ion laser?

(b) Under what circumstances would a diode laser be preferable to an argon-ion or helium-neon laser?

(c) Why are ultraviolet emitting sources avoided?

Reference no: EM131083374

Questions Cloud

Determining the membership cost : A health club membership costs $94, plus $42 per month. Let x represent the number of months and y represent the cost in dollars. How much does the first year's membership cost?
Should nurses allowed to continue working : Many states allow nurses to continue to work while undergoing treatment for addiction to illegal drugs, prescription medications and alcohol - Do you believe these nurses should be allowed to continue working with special limitations on their licen..
Describe your experience in assessing and managing patient : Reflect on a patient who presented with a growth and development or psychosocial issue during your Practicum experience as a student nurse practitioner. Describe your experience in assessing and managing the patient and his or her family. Include ..
What are the sources of band broadening in 13c spectra : How are lines narrowed so that high-resolution spectra can be obtained?
Why are ultraviolet emitting sources avoided : Why are ultraviolet emitting sources avoided?
Research supply and demand curves for gasoline : You operate a delivery service in your local area, but you are thinking of expanding to another market.  You're concerned that you might need to set different prices in the new market because the cost of gas might be much different.
What is the most likely cause of fatigue for this patient : What other questions should the nurse ask about the fatigue? What other assessments would be necessary for this patient?
Calculate the depolarization ratio : Calculate the depolarization ratio and indicate which Raman lines are polarized.
What are factors that have led our legislators : What are the factors that have led our legislators to not identify mental health as an issue for improved health care for our nation?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Assume that the internal energy and specific volume of

the pressure of 200 kgs of water is to be increased from 1 atm to 4 mpa. the water enters through a 20-cm-diameter pipe

  Calculate the specific enthalpy change

What is the kinetic energy (in Btu) associated with a 300 gm hockey puck flying at 120 mph? Assuming an ideal gas, calculate the specific volume in the appropriate units for: Calculate the specific enthalpy change (in the appropriate units) for the f..

  Derive the equations for the dynamic model for the motor

The resistance of the coil is 0.2 ohm. The inductance of the coil is 1.2e-4 H. The rotor inertia is 1.0e-5 kg m2. The current to torque gain is 0.03 Nm/A. The friction torque is 0.09 Nm. A 12 V voltage source is applied to the motor. Derive the equat..

  The figure below shows the geometrical stress concentration

the figure below shows the geometrical stress concentration factor k for a flat bar loaded in uniaxial tension. the

  How does dn differ qualitatively from volume mean diameter

How does DN differ qualitatively from the volume mean diameter Dv

  Domestic hot water supply

Steam at 500 kPa, 300 degrees C is used to heat cold water at 15 degrees C to 75 C for a domestic hot water supply. How much steam per kilogram of liquid water is needed if the steam should not condense?

  Determine the allowable force f in the cable

The strut is 5.75 ft long and is assumed to be pin-connected at both ends.

  Describe the three parts sensortransducer signal

describe the three parts sensortransducer signal conditioning output stage of the following measurement systems

  Sketch the entire process p-v diagram obtain an expression

an ideal gas undergoes two processes in a piston cylinder device from 1-2 a polvtropic compression from t1 and p1 with

  Calculate the factor of safety the designer

A small 6-mm diameter pin was designed using ASTM no. 40 cast iron to withstand an axial compressive load of 3.5kN combined with a tensional load of 9.8 N.m. Calculate the factor of safety the designer m must have used.

  What is the rate of entropy generation within the turbine

Air at 5 bar and 177°C (State 1) is expanded through a turbine to 1 bar and 27°C (State 2). The mass flow rate of air through the turbine is 2 kg/s. Stray heat loss of 53.22 kW occurs to a surrounding at 27°C. Calculate the power (kW) developed by th..

  Determine the flow rate of the fan that needs to be

a desktop computer is to be cooled by a fan. the electronic components of the computer consume 60 w of power under

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd