Which operations appear to be commutative

Assignment Help Electrical Engineering
Reference no: EM131320374

Implement circuits in Logisim that show whether or not the operations AND, OR, XOR, NAND, NOR, and XNOR are commutative. This can be accomplished using circuits with only 3 inputs and 2 operations.

1. Create a table similar to the one in problem

2. Which operations appear to be commutative?

Reference no: EM131320374

Questions Cloud

Explain any legal issues regarding your selected clause : Write a paper of 700- to 1,050-words in which you do the following: Explain any legal issues regarding your selected clause. Explain how your contract clause can be applied in a business managerial setting for either a personal, real, or IP dispute ..
What are the 3 positions of the toggle switch : What components in the circuits implemented in this chapter are directional? How can you determine if you have placed the component correctly?
Presentation - terrorism and cyber crime : Pick a topic from the list below taken from the Cyber Crime course and create a presentation using MS PowerPoint (minimum of 10 presentation slides, and including a slide References). Topics: The Processing of Evidence and Report Preparation, Issue..
Draw the symbols for the nand nor xor and xnor gates : Modify the circuit from question 2 to use a second AND gate on the chip. You should use the same input switches on the circuit, so the resulting lighting of the LED should be the same.
Which operations appear to be commutative : Implement circuits in Logisim that show whether or not the operations AND, OR, XOR, NAND, NOR, and XNOR are commutative. This can be accomplished using circuits with only 3 inputs and 2 operations.
Describe the key components of a data communication system : Describe the key components of a data communication system. Next, discuss the overall manner in which a company uses data communication in order to reduce its operations cost.
Implement the half adder circuit on the breadboard : Using the 2-bit adder presented in the chapter as a model, implement a 4-bit adder in Logisim. Implement an 8 bit adder.
How your own theories of criminal justice have matured : Determine two ways to apply what you learned in this course in your current or a future position. Examine how your own theories of criminal justice have matured or changed since the beginning of this course
Explain nist and risk governance and risk management : "NIST and Risk Governance and Risk Management" Please respond to the following: NIST provides many procedures and much guidance on IT and information security-related topics.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  State three applications of faraday''s law

How would you orient a loop antenna in order to obtain maximum signal from an incident electromagnetic wave which has its magnetic field linearly polarized in the north-south direction?

  Determine the current through the source resistor rs

Determine the current through the source resistor Rs of each network of given figure using either mesh or nodal analysis. .

  How do you draw the standard form simulation diagram

how do you draw the standard form simulation diagram given a higher-order differential equation and how to make

  Design the lpf using blt and butterworth design technique

An ideal C/D converter is followed by a discrete-time LPF which is followed by an ideal D/C converter. The sampling rate is 8000 samples per second. The input analog signal is bandlimited to 3900 Hz. The overall frequency response is required to s..

  Design a phase shift circuit at a frquency

1- Draw a circuit whose output goes to + V sat . When the input signal is below -4V. the output should be -V sat, when the input is above - 4V  2- Design a - 90 phase shift circuit at 1590 Hz , Then for your design calculate 0 at 15 Hz, & 15 KHz

  Design a mealy circuit that recognizes the input sequence

Design a Mealy circuit that recognizes the input sequence 0101 only after the sequence 110 has occured. Show a state diagram, state table, implication table and make a state assignment using the three guidelines.

  Determine the value using a butterworth filter

A vibration trandsucer measures a sinusoidal signal with up to a 100-hz frequency and an amplitude of + and - 5 v. Superimposed on this signal is an additional signal with a freq of 1000 hz. and amplitude of .2

  What is the source of the polarization-holding capability

Why are such fibres sometimes used as polarization-holding waveguides and what is the source of the polarization-holding capability? How can such fibres be fabricated?

  Plot the overall noise figure for both amplifier

calculate and plot the overall noise figure for both amplifier-mixer configurations for FA = 0-10 dB.

  Find what range of integers can be stored in the computer

A computer has a word length of 8 bits (including) sign. If2's complement is used to represent negative numbers, what range of integers can be stored in the computer If 1's complement is used

  Determine cutoff frequency and order for anti-image filter

a dsp system is given with the following specifications: design requirements: sampling rate 20,000 Hz Maximum allowable gain variation from 0 to 4,000 Hz = 2dB 40dB rejection at the frequency of 16000 Hz

  What are the best values for the cutoff frequencies

Various radio stations in a given geographical region are assigned different carrier frequencies so that the frequency ranges of the signals do not overlap. Suppose that a certain AM radio transmitter has a carrier frequency of 980 kHz.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd