Which aspects of project performance were most negative

Assignment Help Mechanical Engineering
Reference no: EM131367842 , Length: 5

Individual Post Mortem Analysis

The Post Mortem analysis is an individual report where you will discuss how the first semester of capstone went. It will be turned into Bb Learn at the beginning of Spring Semester.

This Report must answer questions all of the following questions:

1. Did the team complete the Purpose and Goals stated in the Team Charter?

2. Were the Ground Rules and Coping Strategies stated in the Team Charter followed?What worked and what did not?

3. Which aspects of project performance (time management, product quality, manuf. Cost,etc.) were most positive?

4. Which aspects of project performance were most negative?

5. Which tools, methodologies and practices contributed to positive (or negative) aspects of performance?

6. What problems did the team encounter?

7. What specific organizational actions can be taken to improve performance?

8. What specific technical lessons did you learn?

This Progress Report must include:

An introduction to the report contents

The answers to the above questions organized into the following two categories

o Contributors to project success

o Opportunities/areas for improvement

As this should be in report-style format, each paragraph should flow into the next, from topic to topic. Each paragraph should clearly and smoothly convey which question you are answering without using the question as a header.

The end goal of this Progress Report is that EACH individual team member shows they can constructively analyze the performance of themselves and their team in order to improve upon the second half of the project. When writing about any negative aspects of the first
semester, be sure to word the report in the most positive manner possible.

Reports must be formatted as follows:

- Single spaced

- 11-point font

- Include cover page with:

o Name

o Date

o Team number and name

o Assignment title

o Section information

- Reference page for any sources used

- SUBMIT AS PDF (no Word, .gdoc, Pages, etc.)

- Length: 4-5 pages

https://www.dropbox.com/s/pvoda2yogfr0x0b/final_proposal.rar?dl=0

Reference no: EM131367842

Questions Cloud

Define informal restructuring : Define Informal restructuring; reorganization in bankruptcy, Assignment; liquidation in bankruptcy; fairness; feasibility and Absolute priority doctrine; relative priority doctrine.
How does the music differ between the baroque era and now : After viewing the concert excerpts, construct a comparison of these two concerts. Did you enjoy the concerts? If so, why? If not, why not? How does the music differ between the Baroque era and now?
Why creditors usually accept a plan : Would it be a sound rule to liquidate whenever the liquidation value is above the value of the corporation as a going concern? Discuss.
Complete a timing chart including st wa a b c and d : The SM charts for three linked machines are given below. All state changes occur during the falling edge of a common clock. Complete a timing chart including ST, Wa, A, B, C, and D. All state machines start in the state with an asterisk (*).
Which aspects of project performance were most negative : ME 476C,ME 486:Did the team complete the Purpose and Goals stated in the Team Charter?Were the Ground Rules and Coping Strategies stated in the Team Charter followed?What worked and what did not?Which aspects of project performance (time management, ..
Why do liquidations usually result in losses for creditors : Why do liquidations usually result in losses for the creditors or the owners, or both? Would partial liquidation or liquidation over a period limit their losses? Explain.
Leading a global organization : What leadership skill or trait do you think is essential for leading a global organization? Explain why you think this way. Support your position with references.
Explain what the phrase unity through diversity means : Review the information presented on page 14, including Point to Ponder 1.3. Then, explain what the phrase unity through diversity means and how the metaphor of a tossed salad illustrates this concept.
Communities through prevention and awareness : Our public health system such as the country and state as well as the Center for Disease Control (CDC) has made significant progress in assisting communities through prevention and awareness. Can anyone name a recent (past 2 years) awareness camp..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the damping factor (zeta) of the system

At resonance, the amplitude is measured to be 0.8 cm. At 0.85 resonant frequency, the amplitude is measured to be 0.6 cm. Determine the damping factor (zeta) of the system.

  Heat loss of 03 kw occurs from the compressor to the

air flows steadily through a compressor at the rate of 1.57 kgmin. the compressor requires 5 kw power input to compress

  Derive a formula for the estimated velocity of the flow

If the bending moment M of the rod is measured at the wall, derive a formula for the estimated velocity of the flow.

  Determine the flow rate of the fan that needs to be

a desktop computer is to be cooled by a fan. the electronic components of the computer consume 60 w of power under

  A hollow steel shaft 6 ft long has an outer diameter of 25

a hollow steel shaft 6 ft long has an outer diameter of 2.5 in. and an inner diameter of 1.5 in. the shaft is

  Find the velocity of the satellite relative to that of the

suppose a satellite in geosynchronous orbit has just passed above the international space station with respect to the

  Understand mechanism of hardenability in steels

Understand mechanism of hardenability in steels by Jominy-end quench method - Samples have been heat treated using the following conditions: Austenitizing at about 900oC for 30 minutes, water spray from one end until the whole samples cooled down to ..

  Find the most general bilinear mapping

Find the most general bilinear mapping

  Air at 80oc and a pressure of approximately 1350 kpa abs

air at 80oc and a pressure of approximately 1350 kpa abs flows in a 20-mm-diameter tube. what is the minimum turbulent

  Describe a standard i 5n belt cross section

Specify the standard 3V belt length (from Table 7-2) that would he applied to two sheaves with pitch diameters of 5.25 in and 13.95 in with a center distance of no more than 24.0 in. For the standard belt specified in Problem 1, compute the ac-tual..

  Determine the savings associated with application

Determine the savings associated with application of a 10-mm-thick coating of urethane insulation (k = 0.026 W/m · K) to the outer surface of the pipe.

  Argon gas flows through a rigid nozzle at

argon gas flows through a rigid nozzle at steady-state-steady flow. the inlet flow velocity is small. the gas exits the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd