What would happen to the charge after it crosses resistors

Assignment Help Electrical Engineering
Reference no: EM13280520

a power source is giving 12 V to a circuit. In the circuit there is a resistor. Therefore, would the voltage drop 12 V when the charge moves across the resistor making there 0 V in the circuit after the resistor? This does not make sense to me because if there is 0 V in the circuit, what would happen to the charge after it crosses the resistor? Also, are charges scattered all around the circuit so that a flow of current is all over the circuit at all times?

Reference no: EM13280520

Questions Cloud

Explain how many atoms are in a unit cell : An end-centered orthorhombic unit cell has a cereal-box shape with atoms at each corner and on the face of two opposite ends. How many atoms are in a unit cell
Find the rate of angular acceleration of the disk : A grinder consists of a solid 15 kg disk with a diameter of 57 cm. A when active, the disk rotates at a rate of 83 rad/sec. find the rate of angular acceleration of the disk
Explain lower the melting point of a substance : Using words and pictures, explain why impurities usually lower the melting point of a substance. Next, imagine a case where an impurity actually RAISES the melting temperature of a pure substance
Determine what would be the voltage in the capacitor at t : Suppose that a current x(t) = e^-0.5t for t > or equal to 0, and zero otherwise is applied to a discharged capacitor of capacitance C =1F at t = 0 sec. What would be the voltage in the capacitor at t= 1 seconds
What would happen to the charge after it crosses resistors : a power source is giving 12 V to a circuit. In the circuit there is a resistor. Therefore, would the voltage drop 12 V when the charge moves across the resistor making there 0 V in the circuit after the resistor.
What is the projects year 0 net cash flow : The project requires an initial investment in net working capital of $400,000, and the fixed asset will have a market value of $260,000 at the end of the project. If the tax rate is 30 percent, what is the project's year 0 net cash flow? Year 1? Y..
Explain what is the ratio a/r where a is the edge length : Identical hard spheres of radius R are packed together to form a simple cubic lattice. What is the ratio a/R, where a is the edge length of the unit cell
What is the effective cost of borrowing in this case : Your firm has an average collection period of 25 days. Curret Practice is to factor all receivables immediately at a 1.5 percent discount. What is the effective cost of borrowing in this case?
Which factors influence a person capacity for social mobile : Which factors influence a person’s capacity for social mobility? 850 word each...both question need 5 reference+ the subject text is "Stratification: social division and inequality"

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the armature voltage va at the instant

At some instant, it goes into regenerative braking. Calculate the armature voltage va at that instant, if the current ia is not to exceed 10A in magnitude. Assume that the inertia is large and thus the speed changes very slowly.

  Calculate the radius of curvature of the lower surface

A Newton's ring apparatus is to be used to determine the radius of curvature of a lens (see the figure below and Problem 75). The radii of the nth and (n+16)th bright rings are measured and found to be 0.129 and 0.317 cm

  Find the magnitude and phase as function of f

A military satellite uses 10 GHz for the downlink frequency. The distance to the satellite is approximately 36000 km. if the satellite transmitter produces a power of 50 dBm with a transmit antenna gain of 20 dB and on the ground

  What is frequency that corresponds to frequency bin number

A DSP engineer applies DFT to 500 data samples that are sampled at 250 Hz to plot the signal spectrum. What is the frequency that corresponds to the frequency bin number

  Define mobile communications base station

In a typical mobile communications base station (or cell site), a radio frequency (RF) signal is amplified in the base station and then sent (over cable) to the antennas at the top of the tower.

  Compute efficiency using both exact and approximate circuits

It is operating at 50% of its rated load at a power factor of .5 leading, compute efficiency using both exact and approximate equivalent circuits as referred to the primary side. Tabulate the percent errors in the currents, voltages, powers

  What is the power recieved in the rr-ll and rl polarizations

If a particular radar reciever can detect the target using HH polarization at a maximum distance of 10km, find the maximum distance at which the target can be detected using VV polarization. Assume a standard radar equation.

  What is the maximum distance the trace can be from the ic

A sensitive IC (integrated circuit) on a circuit board is located 1m from a long power line carrying 10A. The power line generates a magnetic field. You can place a trace on a circuit board with current running parallel to the power line to cancel..

  Find the minimized product of sum-pos expression

Using the Karnaugh Map, solve the fallowing expression and answer the question: F= S (4,5,9,13,15) and don't care cells are (0,1,7,11,12). A) Find its minimized Sum of product (SOP) expression. B) Find its minimized product of Sum (POS) expression.

  Develop a series 90-30 program that functions a motor

Design your circuit so that the STOP push button must be pressed before the motor can be switched direction Also incorporated a 5 second delay to inhibit restart after the STOP push button has been pressed Green light

  What is the output do to the given initial conditions

Discrete Systems and Digital Signal Processing Looking for a step by step solution to the following question, y(n) - .6y(n-1) + .6y(n-2) = 0, y(-1) = 0, y(-2) = -1 What is the output do to the given initial conditions

  Compute the number of turns required to permit an elongation

A helical spring is fabricated by wrapping wire ¾ in. in diameter around a forming cylinder 8 in. in diameter. Compute the number of turns required to permit an elongation of 4 in. without exceeding a shearing stress of 18 ksi. G = 12 × 106 psi.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd