What would be the velocity of the sound in the tube for

Assignment Help Mechanical Engineering
Reference no: EM13610780

Estimate in mm your uncertinity in locating the position of a resonance level. Are the resonances " sharp" (located at a single point)? what is the longest wavelength of sound that could produce a standing wave in the resonance tube? (Assume v = 340 m/s ) what frequency is this ? if the air tube were 50 c , what would be the velocity of the sound in the tube ? for fork 1 = 1024 hz what would the wave length be? where would the first resonance be located?

Reference no: EM13610780

Questions Cloud

A block with a weight of 35 n is at rest on a horizontal : a block with a weight of 3.5 n is at rest on a horizontal surface. a 1.2 n upward force is applied to the block by
The author recorded actual temperatures along with : the author recorded actual temperatures along with temperatures that were predicted 5 days earlier. results are listed
Casual comfort textiles corporation began january with a : casual comfort textiles corporation began january with a budget for 30000 hours of production in the weaving
The cannon exerted an average force of 1000 newtons on the : a 14 kg steel ball is launched from a cannon at an angle of 20 degrees above the horizontal. the cannon exerted an
What would be the velocity of the sound in the tube for : estimate in mm your uncertinity in locating the position of a resonance level. are the resonances sharp located at a
After flying for 15 min in a wind blowing 42 kmh at an : after flying for 15 min in a wind blowing 42 kmh at an angle of 28deg south of east an airplane pilot is over a town
Determine the vertical component of the average impulsive : why do we not take into account the normal forces or the frictional forces acting on the jumper when determining the
A company has prepared the operational budget and the cash : a company has prepared the operational budget and the cash budget is now preparing the budgeted balance sheet. to
A cylindrical container 139 m tall contains mercury to a : a cylindrical container 1.39 m tall contains mercury to a certain depth d. the rest of the cylinder is filled with

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compute the steady-state concentration of benzene in the

as a result of a chemical spill benzene is evaporating at the rate of 1 gram per minute into a room that is 6m x 6m x 3

  Determine the average speed

The graph for the motion of a train as it moves from station A to station B is shown. Draw the a-t graph and determine the average speed and the distance between the stations.

  Question 1 bending about two axesthe load p 2 kn is

question 1 bending about two axesthe load p 2 kn is applied to the end of rectangular section cantilever beam shown

  The arm of the robot has a fixed length of r3ft and it

the arm of the robot has a fixed length of r3ft and it grips a moves along the path z3sinthetaft where theta is in

  A vehicle is stuck on the railroad tracks as a 30106 lb

a vehicle is stuck on the railroad tracks as a 30106 lb train is approaching with a speed of 75mph. as soon as the

  Determine the scalar component of the moment

Determine the scalar component of the moment at point 0 about line OB and the reaction at 0 - average normal and shear stresses on plane BB.

  Draw a graph of system head and fluid power

Draw a graph of system head and fluid power against flow rate on one sheet of graph paper, using the values determined in(c)

  Determine the dimensions of the lowest cost container

design an outside storage facility for methane gas ch4. 110 kg is the maximum mass of methane to be stored at this

  Just before arriving to its destination it decelerates at

train starts from rest and accelerates uniformly at 0.35g to reach its max speed of 150 mph. just before arriving to

  Minimum weight design of a variable shape three-bar

minimum weight design of a variable shape three-bar truss.numerical solution using the matlab optimization toolbox

  Determination of the heat transfer coefficient values

this would provide you with a set of Reynolds numbers. Next, using the integral method, determine the velocity profiles within the boundary layer to be followed by determination of the heat transfer coefficient values for your selected Reynolds numbe..

  Draw conclusions concerning the process

Draw conclusions concerning the process, and relate your interpretation to the possible existence of chance and assignable causes of variation.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd