User Account

All Pages

What will be the work of adhesion between water and 100si

Assignment Help Mechanical Engineering
Reference no: EM13618856

What will be the work of adhesion between water and {100}Si plane WSL, if a sessile drop of H2O on the Si surface forms an angle of 33 °, and the surface energy of water in contact with air is 76.10-3 J/m2 (=N/m).

Reference no: EM13618856

Questions Cloud

Milk is pasteurized if it is heated to 63c for 30 min but : milk is pasteurized if it is heated to 63c for 30 min but if it is heated to 74c it only needs 15 seconds for the same
Show that the moving cylinder leaves the fixed one when the : a cylinder of radius a is balanced on top of a fixed cylinder of radius b b gt a . if the balance is slightly
Given n1000 lb e30x106 psi upsilon03 l4 ft gamma0283 lbin3 : given n1000 lb e30x106 psi upsilon0.3 l4 ft gamma0.283 lbin3 and a 4x4 hollow square tube beam cross section with a
The coil of a generator has a radius of 017 m when this : the coil of a generator has a radius of 0.17 m. when this coil is unwound the wire from which it is made has a length
What will be the work of adhesion between water and 100si : what will be the work of adhesion between water and 100si plane wsl if a sessile drop of h2o on the si surface forms an
What is the minimum number of turns area per turn 0018 m2 : the maximum strength of the earths magnetic field is about 6.9 x 10-5 t near the south magnetic pole. suppose we want
A 95 confidence interval for the difference in proportion : a candidate for one of ohios two u.s. senate seats wishes to compare her support among registered voters in the
Draw a schematic of band structure of a compound that has s : draw a schematic of band structure of a compound that has s and p orbitals occupied. show where is the fermi energy and
Two points charges of 200 uc and -800 uc are separated by : two points charges of 20.0 uc and -8.00 uc are separated by the distance of 20.0 cm. what is the magnitude of electric

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The velocity of the air stream decreases from 230 ms to 30

air at 80 kpa and 127 degrees celsius enters an adiabatic diffuser steadily at a rate of 6000 kghr and leaves at 100

  The tank is being filled with water by two one-dimensional

the tank is being filled with water by two one-dimensional inlets.nbspthe water height is h. a find an expression for

  You think this is a polytropic compression process write

you are a new engineer at a company that manufactures gas-filled shock absorbers for racing cars. the chief engineer

  Draw a sketch to represent the stress distribution

Calculate the magnitude of the moment acting at the build-in end and specify the orientation of the moment vector relative to the principal centroidal axes of the section with the aid of a sketch and determine the stresses at each corner of the bu..

  The magnitude and direction of the resultant force

Consider the cylindrical weir of diameter 3 m and lenght 6m.if fluid on the left has specific gravity of 1.6,and on the right has a specific gravity of 0.8,find the magnitude and direction of the resultant force

  Saturated properties out of the evaporator

Assuming saturated properties out of the evaporator and condenser

  Find the cycle cop

An air conditioner in the airport of Timbuktu runs a cooling system using R-410a with a high pressure of 1500 kPa and a low pressure of 200 kPa. It should cool the desert air at 45 degrees C down to 15 degrees C. Find the cycle COP. Will the syste..

  Explain beam deflection at corner through centroid

Beam deflection at corner through centroid, Sometimes the term centroid throws me for a loop. So, how would I set this problem up?

  If we need to maintain the wire at a temperature of 250oc

a tungsten wire 0.005mm in dia and 2 mm in length is placed horizontal in stagnant air. if we need to maintain the wire

  The piston will be moved slowly and reversibly until 25

one kilogram of saturated liquid methane at 160 k is placed in an adiabatic piston-and-cylinder device and the piston

  Determine the reading on the pressure gage in psig when all

a transparent rigid container is filled with 2 gallons of water. initially the pressure is measured to be 10.2 psig

  What is the total force reaction

What is the total force reaction (magnitude) at pin joint O when the square plate is released from rest? Assume the plate has a uniform thickness.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd