What voltage will be indicated by the potentiometer

Assignment Help Mechanical Engineering
Reference no: EM131275973

1. Four chromel-alumel thermocouples are connected in series. The four junctions are at 100, 150, 200, and 250?C. The series arrangement is hooked to a potentiometer, the copper-binding posts of which are at 30?C. What voltage will be indicated by the potentiometer?

2. What could be the thermoelectric sensitivity of a nichrome-aluminum combination? Of a nichrome-constantan combination?

Reference no: EM131275973

Questions Cloud

Assumptions assumed by pearson product moment correlation : What are the scaling assumptions assumed by Pearson product moment correlation?- Identify the type of relationship.
Specify the main points of the buy american requirements : Specify the main points of the Buy American Requirements in one page or less and determine the substantive means by which the Buy American Requirements would benefit both VectorCal and your new company. Provide a rationale for your response
Explain the pathophysiology of the alterations : Explain how genetics, gender, ethnicity, age, and behavior might impact the pathophysiology of the alterations you identified, as well as diagnosis and treatment of your selected disorder.
Describe the partnership life cycle : Describe the partnership life cycle and the various challenges at each stage. Discuss one new technology tool to aid in primary qualitative or quantitative research.
What voltage will be indicated by the potentiometer : . Four chromel-alumel thermocouples are connected in series. The four junctions are at 100, 150, 200, and 250?C. The series arrangement is hooked to a potentiometer, the copper-binding posts of which are at 30?C. What voltage will be indicated by ..
Regulations and rising taxes are hurting the profit margin : You are the CEO of a medium-sized solar panel firm located in California. The company has been doing well so far but new regulations and rising taxes are hurting the profit margin. You have been negotiating with the Governor a tax reduction because o..
Describe the culture of your organizational behavior : Describe the culture of your organizational behavior issues and what challenges are present - discuss the systems that are the most appropriate to introduce into your organization.
Business afford not to take advantage of popularity : Can a business afford not to take advantage of the popularity of Facebook and other social media sites to help grow their business? Is social media that important to business that they must take part?
Find the emissivity of the metal part : Using the results of Prob. 8.47, determine the true metal temperature when the pyrometer indicates 450?C and the uncertainty in this temperature.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  An air intake duct has a 14x14 opening the duct is 18 long

an air intake duct has a 14x14 opening the duct is 18 long with an exaust opening at the other end that is 14x1 giving

  Transfer function between elevator input and pitch attitude

The transfer function between the elevator input and the pitch attitude of a plane is given by: Design an autopilot controller (using a lead compensator) for the system so that the response to a step input (pitch command) has a rise time of 1sec or l..

  What is the general construction of hydraulic motors

What is the general construction of hydraulic motors similar to?

  Determine the heat flux across the steel sheet

A 10 mm thick Teflon sheet is perfectly bonded to a large 9 mm thick type 316 stainless steel sheets. The interface is at 119?C and the outer surface of the steel sheet is at 120?C. Take K Teflon = 0.25W/m.K K 316 Steel = 13.4 W/m.K In steady state, ..

  What fraction of the benzene is recovered in the

the 3m company removes benzene from synthetic resin-based sandpaper by passing the sandpaper product through a dryer in

  When it is initially filled with gas at 100 deg c what is

a small steel cylinder is used as a pressure vessel for a paint gun. the label says 24 grams co2 filled. assume the

  Sampled digitally at sampling frequencies

A sine wave at frequency f= 90 Hz is sampled digitally at sampling frequencies fs=200,160 and 50 Hz respectively. For each case, discuss whether there is aliasing. Also for each case, calculate the aliasing (perceived) frequency.(b) Using EXCEL (or M..

  Design an annealing treatment for a 1050 steel

Design an annealing treatment for a 1050 steel. Be sure to include details of temperatures, cooling rates, microstructures, and properties.

  Determine the equation of the neutral axis under

If the allowable stresses in tension and compression are 76 MPa and 52 MPa respectively, find the maximum permissible load Pmax.

  The average temperature on each side of the door

Consider a wooden door with a glass window. The door is 5 cm thick and 0.75 m wide by 2 m tall. The window is 0.2 m square and 1 cm thick. The air on one side of the door has a temperature of 23°C and a heat transfer coefficient of 10 W/m2-K. The air..

  What is meant by the mechanical loss coefficient of a

what is meant by the mechanical loss coefficient ? of a material? give examples of designs in which it would play a

  Qualitative difference between the sine and tangent results

Determine the percent error n in replacing the sine and the tangent of an angle by the value of the angle in radians for angle values 5 degrees, 10 degrees, and 20 degrees. Explain the qualitative difference between the sine and tangent results.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd