What value of load resistance would produce greatest amount

Assignment Help Electrical Engineering
Reference no: EM13272609

You happen to have a 5-V regulated power supply that you bought at Midwest Surplus Electronics in Fairborn, Ohio. Measuring the output voltage with your trusty voltmeter, you get an open-load reading of pretty close to 5 V. When you connect a 10-O wire-wound power resistor to the output, however, the voltage sags to 4.5 V. Use this information to find the effective output resistance of the power supply. What value of load resistance would produce the greatest amount of transferred power into this load? How much is this power? If the load was actually a homemade heating coil wound around a section of aluminum pipe 1.5" in diameter, how many turns of 18-gauge wire would be necessary, given that 18-AWG copper wire has a linear resistance of 6.385 mO per foot? Draw all circuits and explain your results.
Hint:
Assume that each turn of wire will have a length approximately equal to the pipe's circumference. Although the length of each turn will become slightly longer as more layers of wire are wound on the pipe, assume that this effect is negligible.

Reference no: EM13272609

Questions Cloud

Calculate the mortgage constant : You borrow $75,000 for 30 years at 11% interest compounded annually. The value of the property is $100,000, PGI= $20,000, vacancy rates are 8%, and operating expenses are $8,100.
What is the mass of the bullet : A bullet is fired at a stationary wooden block at 200 m/s. The mass of the block is 2kg the bullet embeds in the block during the collision. What is the mass of the bullet
Derive the relationship between the voltage across resistors : Derive the relationship between the voltage across the 1 resistor and the magnetic intensity, H. Hint: explore the relationship between magnetomotive force and magnetic intensity as discussed in the overview.
Compute the conversion premium : At what price does the common stock need to sell for the conversion value to be equal to the current bond price? Stock price = $
What value of load resistance would produce greatest amount : You happen to have a 5-V regulated power supply that you bought at Midwest Surplus Electronics in Fairborn, Ohio. Measuring the output voltage with your trusty voltmeter, you get an open-load reading of pretty close to 5 V.
Reduce your anxiety about writing : What knowledge about writing, the writing process, and/or yourself as a writer did you learned that has helped you to reduce your writing anxiety?
What will happen to the operating cash flows : You are in charge of a project that has a degree of operating leverage of 2.64. What will happen to the operating cash flows if the number of units you sell increase by 4 percent?
Which of following would lead to decrease in working capital : Other things held constant, which of the following would lead to a decrease in working capital?
What bid price per carton should you submit : Assume that your tax rate is 34% and you require a 10% return on your investment. What bid price per carton should you submit?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is leakage current of aluminum electrolytic capacitor

An Aluminum electrolytic capacitor that has a capacitance of 75,000µ F,100WV is used in a power supply circuit. The leakage specification of this type of capacitors is 5µ A/µ F. If the voltage across this capacitor is 50 volts, what will be the le..

  What is minimum coefficient of friction that prevent sliding

what is the minimum coefficient of friction that will prevent sliding.

  Determine of power density that is reflected from interface

A 100 MHz plane wave is incident from air onto a dielectric medium ( \(\epsilon=\epsilon _{o}\) ) at normal incidence. Find the below. a. \(\Gamma \) and SWR b. \(\lambda \) in air and in dielectric c. Percentage of power density that is reflected f..

  What is the perceived colour if three colors are mixed

what is the perceived colour if you mix red ,green and blue dyes in equal proportion and why  What about red and green frequiencies only

  Design a dc power supply that provides energy absorber

Design a DC power supply that provides -95v +/- 5v to a 2 amp load (energy absorber). The input source is a 100 volt peak sinusoid, 60 Hz. You may use any basic circuit element. State the values of all circuit elements (in ohms, farads, etc).

  Explain the significance of terms such as loading effect

Summarize when and why it is important to use the "50 O" termination setting on the function generator (with the corresponding 50- O terminator in your circuit, of course). In which situations would this not be necessary

  Determine the total mvar and the capacitance per phase

Shunt capacitors are installed at the receiving end to improve the line performance. The line delivers 70 MVA, 0.8 lagging power factor at 64 kV. Determine the total Mvar and the capacitance per phase of the Y-connected capacitors.

  Determine number of bit that must be specified for converter

A successive approximation A/D converter with range of 0 to 5 volts and a resolution of 0.05 volts is specified. It will be clocked at 500 KHz. a. Determine the number of bits that must be specified for this converter. b. Determine the t..

  How big the capacitance connected on series with resistor

how big will be capacitance connected on series with resistor R=30 omega in AC circuit with input voltage U1 = (200+2*17) V and frequency 50 Hz if the power factor is 0.7

  Provide the foundation for a lasting relationship

Noise is generally viewed as one of a number of general biological stressors. It is felt that excessive exposure to noise might be considered a health risk as noise may contribute to the development and aggravation of stress related conditions suc..

  What is difference between block diagram and front panel

What does the DAQ Assistant do How is it useful over the legacy acquisition methods What does FFT stand for and what does it do to a real-time signal Sketch the output of an FFT analysis performed on a 100 Hz sinewave signal at 1 V.

  What would total bus 3 impedance be including impedance

The parts of this problem refer to the reflection method of solving real transformer problems: A.What is the value of Zload projected into bus (Region) 2 B.What is the total impedance of bus 2 including the projection

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd