What torque must be applied to the shaft to overcome the

Assignment Help Mechanical Engineering
Reference no: EM13635489

1. A 500 ml cylindrical mug is filled level with the top of the mug with 90°C water. What is the water level relative to the top of the mug if the water is cooled to 20°C? The diameter of the mug is 10 cm. Ignore any surface tension effects.

2. A 4 cm diameter shaft is held in place by a bushing with an inside diameter of 4.1 cm. The bushing has a length of 1.5 cm and is lubricated with SAE 50 Oil at 80oC. If the shaft is rotated at a constant speed of 4500 rpm:

a. What torque must be applied to the shaft to overcome the fluid shear stress to maintain this rotational speed?
b. What power (in W) would be required to maintain this speed?

3. One way to study the surface tension effects in a liquid/solid system is to dip a pair of parallel plates into the container of the liquid. How far up in a pair of parallel glass plates, 0.3 mm apart, would water at 40oC be drawn up?

4. A 5 kg block is supported on a thin film of an unknown liquid 0.2 mm thick on an incline of 10o. Determine the viscosity of the liquid if the terminal velocity is 5.678 m/s. Assume the velocity distribution in the gap is linear, and the area of the block in contact with the oil is 0.25 m2. What is the possible identity of the liquid if the temperature is 20°C?

Reference no: EM13635489

Questions Cloud

A hospital patient has been given 131i half-life 804 days : a hospital patient has been given 131i half-life 8.04 days which decays at 4.4 times the acceptable level for exposure
A steel ball is dropped from a buildings roof and passes a : a steel ball is dropped from a buildings roof and passes a window taking 0.128 s to fall from the top to the bottom of
A 04268 gram sample of a a potassium hydroxide-lithium : a 0.4268 gram sample of a a potassium hydroxide-lithium hydroxidemixture requires 30.88 ml of 0.3535 m hcl for its
Test statistic and value p-value conclusion label the test : a simple random sample of 16 different cereals is obtained and the sugar content in grams of sugar per gram of ceral is
What torque must be applied to the shaft to overcome the : 1. a 500 ml cylindrical mug is filled level with the top of the mug with 90degc water. what is the water level relative
A solution containing 0200 mnh3 and 0020 m nh4cl was : a solution containing 0.200 mnh3 and 0.020 m nh4cl was diluted with water in the proportions shown below volume
A transverse wave is traveling on a string the displacement : a transverse wave is traveling on a string. the displacement y of a particle from its equilibrium position is given by
What are the magnitude and direction of the balls velocity : in a friendly game of handball you hit the ball essentially at ground level and send it toward the wall with a speed of
Determine the value of heat flux that must be supplied by : the air inside a chamber at 54 c is heated convectively with heat transfer coefficient of 35 wm2k by a 0.29-m thick

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd