What should the bungee cords relaxed length

Assignment Help Mechanical Engineering
Reference no: EM13216550

As shown, a 150 lb bungee jumper wants to jump from the top of a 630 ft high bridge and be able to just touch the water below. Given that the bungee cord has a spring constant of 108 lb/ft, what should the bungee cord's relaxed length, l, be for this jump?

Reference no: EM13216550

Questions Cloud

Analyze the performance of eastern electronics : Analyze the performance of Eastern Electronics over the 20x3 through 20x6 time period. Also, determine if the budget projections in 20x7 and 20x8 indicate any changes either favorable or unfavorable in the company performance.
Calculate the force necessary to cause : A cylindrical specimen of this alloy 24 mm in diameter and 186 mm long is to be pulled in tension. Calculate the force necessary to cause a 0.0119 mm reduction in diameter. Assume a value of 0.33 for Poisson's ratio.
Explain federal and state legislators pass laws : On the flip side, should federal and state legislators pass laws assuring the contract and temporary worker access to the same privileges and perks that regular employee counterparts enjoy? Compare and contrast the alternatives.
Determine the temperature at which the treatment was carried : If after 49.5 h the concentration of carbon is 0.35 wt% at a position 4.0 mm below the surface, determine the temperature at which the treatment was carried out.
What should the bungee cords relaxed length : As shown, a 150 lb bungee jumper wants to jump from the top of a 630 ft high bridge and be able to just touch the water below. Given that the bungee cord has a spring constant of 108 lb/ft, what should the bungee cord's relaxed length, l, be for t..
Determine the time required and the distance traveled : An elevator descends from rest with an acceleration of 5 ft>s2 until it achieves a velocity of 15 ft>s. Determine the time required and the distance traveled.
Define organizational model to drive ethical decision making : Describe how organizations can utilize the models to drive ethical decision making, including how those organizations might integrate the model into their business ethics programs.
Business line-up exhibit good strategic fit : Does addidas’ business line-up exhibit good strategic fit? What value- chain match-ups exists? What opportunities for skill transfer, cost sharing, or brand sharing are evident?
Demographic transition patterns of fertility : In the third stage of the (classic) demographic transition patterns of fertility are not entirely predictable nor do they result in unproblematic patterns of population growth.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the irreversible head loss of the valve

Water flows at a rate of 20 l/s through a horz pipe dia .03 m. The pressure drop across the valve in the pipe is measured to be 2 kPa. Determine the irreversible head loss of the valve, and the useful pumping power needed to overcome the resulting..

  Determine the angular velocity

Determine the angular velocity of the two 10-kg rods in Fig. 2 when , if they are released from rest in the position . Neglect friction.

  Determine the surface temperature of the wire

Determine the surface temperature of the wire during a windy day when the air temperature is 10°C and the wind is blowing across the transmission line at 50 km/h.

  Determine the maximum horizontal displacement

Determine the maximum horizontal displacement s of the block. Each of the two springs has a stiffness of k = 2500N/m and an unstretched length of 0.15 m.

  Explain longitudinal versus transverse vibrations in a bar

Longitudinal versus Transverse Vibrations in a bar, A 48 inch long by 2 inch diameter round steel rod (E=30e6 psi, density=0.28 lb/in3) is fixed at one end and free at the other. If the rod is struck transversely so that there is both a longitudin..

  Explain volocity of an airplane was changed

Acceleration was uniform. If it assumed that the acceleration was uniform where the magnitute of the volocity of an airplane was changed from 120mph to 360mph in 6 seconds.

  What input voltage will be computed by the adc

A successive approximation ADC has 4 bits and a reference voltage of 10 V. If the input voltage is 2.8 V, describe each step the ADC undergoes to determine the value of the 4 bits. What input voltage will be computed by the ADC?

  What are production conditions under which group technology

What are the production conditions under which group technology and cellular manufacturing are most applicable?

  Minimum weight design of a variable shape three-bar truss

Obtain a new solution, and determine whether any buckling constraints are active. If no buckling constraints are active for L = 10 in., re-run the analysis by increasing L , and estimate the value of L at which at least one buckling constraint b..

  Investigating a dynamic movement in polar coordinates

Investigating A Dynamic Movement in Polar Coordinates

  Determine the elevation difference

the manometer shown above in problem 1 above contains water and kerosene. with both tubes open to the atmosphere, the free surface elevations differ by H=20mm determine the elevation difference when a pressure of 98.0 Pa is applied to the right.

  Identify the information used to make the decision

Given a simulator or actual device, identify if a control loop is in control or out of control and identify the information used to make the decision

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd