What power is required to drive each screw when the gate is

Assignment Help Mechanical Engineering
Reference no: EM13618612

Two identical 3 in. major-diamter power screws (single-threaded) with modified square threads are used to raise and lower a 50-ton sluice gate of a dam. Quality of construction and maintenance (including lubriation) are good, resulting in an estimated friction coefficient of only 0.1 for the screw. Collar friction can be neglected, as ball thrust bearings are used. Assuming that, because of gate friction, each screw must provide a lifting force of 26 tons, what power is required to drive each screw when the gate is being raised at the rate of 3ft/min? What is the corresponding rotating speed of the screws?

Reference no: EM13618612

Questions Cloud

If the net profit margin is 5 asset turnover is 200 the : if the net profit margin is 5 asset turnover is 2.00 the equity multiplier also called financial leverage ratio is 4.00
A wheat grower expects to have 40000 bushels of wheat to : a wheat grower expects to have 40000 bushels of wheat to sell in three months. the wheat futures contract on the
Two billiard balls of equal mass undergo a perfectly : two billiard balls of equal mass undergo a perfectly elastic head-on collision.if one balls initial speed was 1.80ms
The last dividend on gte stock was 4 and the expected : the last dividend on gte stock was 4 and the expected growth rate is 10. if you require a rate of return of 20 what is
What power is required to drive each screw when the gate is : two identical 3 in. major-diamter power screws single-threaded with modified square threads are used to raise and lower
The wall street journal reports that the rate on 3-year : the wall street journal reports that the rate on 3-year treasury securities is 7.25 and the rate on 4-year treasury
If we need to maintain the wire at a temperature of 250oc : a tungsten wire 0.005mm in dia and 2 mm in length is placed horizontal in stagnant air. if we need to maintain the wire
One-year treasury bills currently earn 475 percent you : one-year treasury bills currently earn 4.75 percent. you expected that one year from now one-year treasury bill rates
The amortization of flotation costs reduces taxes and thus : new york waste nyw is considering refunding a 50000000 annual payment 14 percent coupon 30-year bond issue that was

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine a suitable length for the bolt rounded up to the

a 1.5 inch thick steel plate and a 0.5 inch thick cast iron plate are compressed with 14- 20 unc grade 5 bolt and

  What should the diameter of the nozzle outlet be

What should the diameter of the nozzle outlet be in inches and what is the mass flow rate of steam through the nozzle in lbm/min?

  What is the actual strain

You have a 120 Ω quarter bridge 2 wire set up with Sg=2.10 and an unknown lead wire resistance. A 59880Ω calibration resistor is switched in parallel to the gage only and a recording instrument is set to give a -100 mm deflection for this calibrat..

  Determine the amount of heat transferred kj during the

the free-moving piston-cylinder device shown contains 5kg of hydrogen initially at a temperature of 400degc. when

  Determine the average shearing stress in the bolts

a beam consists of three planks connected as shown by 3/8 in diameter bolts spaced every 12in.along the longitudinal axis of the beam.knowing that the beam is subjected to a 2500lb vertical shear, determine the average shearing stress in the bolts..

  Consider a concentric tube annulus for which the inner and

consider a concentric tube annulus for which the inner and outer diameter are 25 and 50 mm. water enters the annular

  What will the temperature of the r134a be when the piston

a piston cylinder device initially contains 0.5 kg of r134a at 200 kpa and a specfic volume of 0.07 m3kg. at this point

  Find the possible range of the transfer function suppose a

a temperature sensor has a transfer function of 5 mvoc with an accuracy of plusmn 1.5 a find the possible range of the

  Calculate the heat emitted to the environment btusec the

a 600 mw coal-fired power plant has an overall thermal efficiency of 38. it is burning coal that has a heating value of

  Estimate the mass flow rate of fuel into the engine

Estimate the mass flow rate of fuel into the engine in kg/h.

  Oxygen is flowing through a nominal 2 inch schedule 40

oxygen is flowing through a nominal 2 inch schedule 40 steel pipe pipe at a velocity of 10 fts. the oxygen is at a

  Write heat equation and boundary conditions

A long electric wire of radius r0 generates heat at rate of q'''. The surface is maintained at uniform temp of T0. Write heat equation and boundary conditions for steady state one dimensional conduction.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd