What percent of the time is the order actually running

Assignment Help Mechanical Engineering
Reference no: EM131235453

In problem 6.2, what percent of the time is the order actually running?

Problem 6.2

An order for 100 of a product is processed on work centers A and B. The setup time on A is 50 minutes, and run time is 5 minutes per piece. The setup time on B is 60 minutes, and the run time is 5 minutes per piece. Wait time between the two operations is 5 hours. The move time between A and B is 40 minutes. Wait time after operation B is 5 hours, and the move time into stores is 3 hours. Queue at work center A is 25 hours and at B is 35 hours. Calculate the total manufacturing lead time for the order.

Reference no: EM131235453

Questions Cloud

What is your uncles deal worth to you : If you promise to go to school then your even richer Uncle Vinny will buy you a Ferrari provided his business can afford it. - The risk-free rate is 6%. What is your uncle's deal worth to you?
Calculate the saving in manufacturing lead time : Move time between operations is 30 minutes. Work center 20 cannot be set up until the first lot arrives. Calculate the saving in manufacturing lead time.
Should carlos have been discharged : Given the facts of this case, should Carlos have been discharged? Why or why not? ?Should employees of DDP be held to a higher standard of personal conduct than ?employees for other types of organizations? Explain.
What is the amount of net income reported : An analysis of the transactions of Canary Cola, Inc. for the year 2009 yields the following information: revenue, $ 70,000; Supplies expense, $30,900, rent Expense $24,000 and dividents, $ 7,000.
What percent of the time is the order actually running : In problem 6.2, what percent of the time is the order actually running?
Describe the outcome of the change initiative : Describe whether the change proposed and/or implemented in your school or district was/is in alignment with what the research says is best practice in that regard. Then describe the outcome of the change initiative and how you felt about the chang..
Review the documents honest teas business plan : Review the following documents: Honest Tea's business plan for 1999 (PDF). A strengths, weaknesses, opportunities, and threats (SWOT) analysis based on Honest Teas' business plan (PDF).
What cost of capital would you recommend : Assuming an equity premium of 4% and a risk-free rate of 3%,  - what cost of capital would you recommend for 1 year of this firm's cash flows?
Calculate the total manufacturing lead time for the order : Wait time after operation B is 5 hours, and the move time into stores is 3 hours. Queue at work center A is 25 hours and at B is 35 hours. Calculate the total manufacturing lead time for the order.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Show the process on a t-v diagram label axes with respect

one kilogram of ammonia initially saturated vapor at -4degc undergoes a constant volume process to a final pressure of

  Bearing is subjected to the loads-inner race rotate

The bearing (inner race rotate) is subjected to the loads as shown in Fig. 2 (next page). The shaft diameter is 30 mm. The shaft rotates at 655 rpm for 9000 hours life. Select ball bearings (load rating) for position A and C. Assume initial values. X..

  Determine the change in entropy

Five kg of nitrogen (N2) undergoes a process from p1 = 5 bar, T1 = 400K to p2 = 2 bar and T2 = 500K. Assuming ideal gas behavior, determine the change in entropy, in kJ/K

  Thermal conductivity of compacted snow

The thermal conductivity of compacted snow is 0.15 W/m · K. The temperature of the ice cap on which the igloo sits is -20°C and has the same thermal conductivity as the compacted snow.

  Provide rotary actuation in both directions

Draw a circuit diagram to provide rotary actuation in both directions using a single direction pump (to replace the bi-directional pump) and providing a means of preventing over-speeding in the case of an overhauling load in both directions.

  What will be the heat supplied

If the output of a gas turbine is 300 KW and its efficiency is 20 percent, what will be the heat supplied

  Calculate the angular velocity and angular acceleration

Calculate the angular velocity and angular acceleration of a 2kg mass rotating in a horizontal circle of 2m radius if one revolution takes 4 seconds. An object rotates in a 3m diameter circle with angular velocity of 3 rad/s. calculate the period anf..

  Determine the temperature distribution in the sphere

A medical investigator is proposing to use radioactive spheres for thermal ablation of tumors. The idea is that the radioactivity will generate heat at a constant, uniform rate, G (J m-3 s-1), that will raise the temperature of the sphere relative to..

  Positive direction of the x axis

What are the x- and y - components of a vector ii in the xy plane, if its direction is 250°counterclockw ise from the positive direction of the x axis and its magnitude is 7.3 m?

  The braking machanism on an aircraft carrier can bring a 2

the braking machanism on an aircraft carrier can bring a 2 ton plane to a stop in a time of 1.8 seconds. the plane

  Use work and energy to determine the center of mass

bar ab of mass m and mass moment of inertia i 112ml2 is constrained to move within the channel as shown. the bar is

  Liquid in a tube varies with tube diameter

The capillary rise, h, of a liquid in a tube varies with tube diameter, d, gravity, g, fluid density, roe , surface tension, Y, and the contact angle, B. (a) Find the dimensionless form of this statement. (b) If h = 3 [cm] in a given experiment, what..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd