Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
An aluminum cylindrical strain gage load cell is to be specified tomeasure a force of 100,000lbs. The maximum stress in the metal isto be 20,000 psi, the modulus of elasticity is 9.5 x 106psi, and Poisson' ratio is 0.33. What must be the wallthickness of a 6 inch outside diameter cylinder?If it is instrumented with four active strain gages on awheatstone bridge, two axial and two transverse as shown, with S,i.e. strain gage factor of 2.1, initial resistance of strain gagesR = 350 Ω, and the power supply is 10V, what will be theoutput at the maximum load?
A certain parallel circuit coornsists of onrely 1/2 W resistors each having the same resistance. The total resistance is 1 k ohm and the total current is 50mA. If each resistor is operating at one-half its maximum power level
The spring of the pressure gauge shown in the figure below has a force constant of 1385 N/m, and the piston has a radius of 1.00 cm. As the gauge is lowered into water, what change in depth causes the piston to move in by 0.750 cm
The voltage and current at the terminals of the circuit element are zero for t or =0 they are: v = (16,000t + 20)e^-800t V; i = (128t + 0.16)e^-800t A a) At what instant of time is maximum power delivered to the element
What is the maximum power dissipated in the load when the Thévenin voltage is 17 V cos(37 rad/s t + 24°), the Thévenin impedance is 127 -j 182-ohm and the load impedance is 127 + j 182-ohm
Design a 4-bit synchronous up/down counter using T flip-flops. The circuit has one input up' /down such that input 0 means count up and input 1 means count down. up' is "up" with a bar over it
Suppose that we are designing a cardiac pacemaker circuit. The circuit is required to deliver pulses of 1-ms durstion to the heartthat can be modeled as a 500-Ω resistance. The peak amplitudeof the pulses is required to be 5 V.
discuss to describe as best as possible an automatic garage door opener system. You should either use one you are familiar with as an example, or recall the details from one or more that you imagine could be available
sketch a layout that matches two capacitors of unit size 8 and 3.75.The key is to match the perimeter-area ratio.Assume the unit capacitors are sized 4um*4um. Make sure to give the non-unit capacitor dimensions.
In a 2-pole, three phase PMAC synchronous motor, the torque constant kT and the voltage constant kE are 0.6 in respective MKS units. The synchronous inductance, LS is 10 mH. The stator winding resistance per phase is 1 Ω.
Write a 68000 assembly program to calculate the closest integer cubic root of a 16-bit signed number, saved in memory at a location labeled "NMBR". Obligatory Note: Use the subroutine concept in your solution
Construct the adder for 2 digit decimal numbers presented in BCD code. 4 bit binary adders and additional logical gates. The BCD adder for each decimal digit can be implemented with two 4 bit binary adders where the second adder.
A sinusoidal voltage source of v(t) = 170 cos(2pi 60 t) V is applied to a nonlinear load, resulting in a nonsinusoidal current that is expressed in Fourier series form as i(t) = 10 cos(2pi 60t + 30) + 6 cos (4pi 60t + 45) + 3 cos(8pi 60t + 20) A.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd