What kinds of sensors would be needed for the control system

Assignment Help Mechanical Engineering
Reference no: EM131199766

A magnetically levitated rail vehicle uses the principle of induction motor for traction. Magnetic levitation is used for the suspension of the vehicle slightly above the emergency guide rails. Explain the operation of the traction system of this vehicle, particularly identifying the stator location and the rotor location. What kinds of sensors would be needed for the control systems for traction and levitation? What type of control strategy would you recommend for the vehicle control?

Reference no: EM131199766

Questions Cloud

Define a problem or challenge within your topical area : Define a problem or challenge within your topical area that you understand in some depth or have an interest in (examples include high crime rate, poor morale, high levels of violence or recidivism.
Why have self-defense militias sprung up in some rural areas : If Mexico's constitution guarantees the right to gun ownership, then why it is so difficult to purchase guns legally there compared to the United States? Explain. Why do gun advocates in Mexico believe their government's position on guns is "idiotic"..
Prepare the balance sheet for glass company : Prepare the entry that Glass Company would make to record the purchase. - Prepare the balance sheet for Glass Company immediately following the purchase.
Derive the equation from demand curve : 1. Derive the equation from your demand curve from the two price and sales points 2. Are you currently operating in the elastic or inelastic portion of your demand curve?
What kinds of sensors would be needed for the control system : What kinds of sensors would be needed for the control systems for traction and levitation? What type of control strategy would you recommend for the vehicle control?
Describe the operation of a single-phase ac motor : Describe the operation of a single-phase ac motor. List several applications of this common actuator. Is it possible to realize a three-phase operation using a single-phase ac supply? Explain your answer.
Describe the organization and comment on the hr change : Describe the organization and comment on the HR change that the organization should make. Utilize effective diagnostic tools to assess the organizations ability to change. Support assertions with theoretical evidence.
Describe the performance-expectations gap : What was the public issue facing The Coca-Cola Company (TCCC) in this case? Describe the "performance- expectations gap" found in the case - what were the stakeholders' concerns, and how did their expectations differ from the company's performance?
How mcdonald frontline employees demonstrate outcomes of tms : From your experience or observation, how do (or don't) McDonald's frontline employees demonstrate the outcomes of the TMS? What behaviours might be used to evaluate its effectiveness

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The hot gas supply to a propulsion nozzle is at a pressure

the hot gas supply to a propulsion nozzle is at a pressure of 55kpa and temperature of 800k. the ambient pressure is

  You measured the surface heater temperature to be 120oc

you have an electrical heater to heat-treat polymers. according to the manufacturers manual the heat flux at the

  What is the stagnation pressure on the body

A body moves through standard air at 200 m/s. What is the stagnation pressure on the body? Assume (a) compressible flow and (b) incompressible flow.

  Find the compressor efficiency and the entropy generation

An adiabatic compressor is used to bring saturated water vapor at a pressure of 103 lbf/in^2 up to 1000 lbf/in^2 , where the actual exit temperature is 1000 F degree. Find the compressor efficiency and the entropy generation. is there an improvement ..

  Estimate the elastic strain in copper at the yield stress

Illustrate different techniques by which this could be done. Explain why a ceramic coating and discuss the advantages of the three techniques. You may use appropriate examples and references - Estimate the elastic strain in copper at the yield stre..

  A 500 kw compressor is being designed to operate on air in

a 500 kw compressor is being designed to operate on air in a space where the temperature is 300 k and pressure is 90

  Determine the radial and tangential stress distributions

A steel flywheel 25 mm thick with an outer diameter of 1 m and an inner diameter of 200mm is rotating at 100 hz. Determine the radial and tangential stress distributions as a function of radial position r. Plot the distribution

  What had to happen to initiate flow from the drain hose

determine the flow rate from the pool at the instant shown if the hose has an inside diameter of 0.5 in. What had to happen to initiate flow from the drain hose? ·what will happen to the flow rate as the level of the pool drops?

  Write down the characteristic equation of the system

Write down the characteristic equation of the system. What is the order of the system?

  Question regarding the rate of heat transfer

The water experiences a temperature rise of 8°C. The air leaves the cooling section saturated at 20°C. Determine (a) the rate of heat transfer, (b) the mass flow rate of the water, and (c) the exit velocity of the air stream.

  Assume the mouth of the container is narrow enough that in

a fan is blowing 32f air over a container filled to within 1 inch of the top with a solution of ethyl alcohol in water.

  The metered mass flow rate of hydrogen in 50 kgs and 20

you are designing a centrifugal compressor system to compress hydrogen at 200 kpa absolute to 7000 kpa absolute

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd