What is turns ratio of a step-down transformer

Assignment Help Electrical Engineering
Reference no: EM13225566

A 115/28 V transformer has 56 turns on its low voltage side. How many turns does it have on its high voltage side? what is its turns ratio when it is used as a step-down transformer? as a step-up transformer?

Reference no: EM13225566

Questions Cloud

How does the market-driven approach : How does the market-driven approach illustrate that HR has strategic, operational, and administrative roles at SYSCO?
What is the input voltage and output voltage : A transformer is used to match an 8 ohm speaker to a 500ohm audio line. What is the turns ratio of the transformer what is the input voltage and output voltage when 15W is being delivered to the speaker
Explain the oxygen atom forms a s bond : The oxygen atom (with its 2s orbital) forms a s bond with one of the three sp2 hybrid orbitals of the carbon atom; the two hydrogen atoms (with their 1s orbitals) each form a s bond with one of the three sp2 hybrid orbitals of the carbon atom.
Implements a put option hedge : Determine the amount of dollars that Narto Co. expects to receive at the end of 1 year (after accounting for the option premium) if it implements a put option hedge.
What is turns ratio of a step-down transformer : A 115/28 V transformer has 56 turns on its low voltage side. How many turns does it have on its high voltage side what is its turns ratio when it is used as a step-down transformer
Explain the high-high theory of leadership effectiveness : Explain the "high-high" theory of leadership effectiveness. a. How strongly does research evidence support this theory?
Describes new zealand''s physical landscape : Which of the following statements best describes New Zealand's physical landscape?
Identify an additional strategic consideration : Include health insurance, time off, retirement and savings plans, and one other work or life benefit. Explain to management the primary strategic consideration involved in managing the proposed benefits program. Identify an additional strategic consi..
What is a learning organization : What is a "learning organization?" What kind(s) of "learning" may occur in this type of organization?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Define a series circuit has a dc voltage source

A series circuit has a DC voltage source (56 volts), a resistor, (72 ohms), a capacitor (82 farads), and a switch. The capacitor is initially uncharged and the switch closes at t=0.

  Define the gain of the antennas must be increased

The gain of the antennas must be increased when the TDMA system described in part (d) is used because the bit rate is higher than with FDMA and the noise power in the receiver is therefore higher

  What is the cyclic prefix length

An OFDM system with a passband bandwidth of 10 MHz and carrier frequency of 1 GHz is used in an outdoor environment with a maximum delay spread of 15 microseconds.

  Locate and specify an appropriate sensor

Locate and specify an appropriate sensor if it is to operate at 120 vac as an input to a PLC. Create the ladder diagram program to accomplish the specified control.

  Find the laplace transforms and the region of convergence

By direct integration find the Laplace transforms and the region of convergence of the following functions

  Draw a suitable circuit that includes a resistor

Place the relay in the Collector circuit, the resistor in the Base circuit and the diode in parallel with the relay to provide a path for current due to energizing the relay.

  Explain current to voltage op amp circuit

Current to Voltage Op Amp Circuit, A 12-bit DAC (Digital to Analogue Converter) gives an output range of 0 to 1 mA for a digital input word of 0 to 4095

  How much current is flowing through the resistor

If I have a resistor that is 10 Ohms and has a voltage drop of 4.2 V, how much current is flowing through the resistor?

  What are the four characteristic parameters

What are the four characteristic parameters of transmission line? Which parameter is used to calculate the real loss? Which parameter is used to calculate the charging current? Which parameter is almost negligible and why?

  Efficiency of mosfet circuit

Efficiency of MOSFET circuit provide in datasheets of any product is measured at transient state of my output node or staedy state?

  Determine the atomic radius of a single aluminum atom

aluminum has the FCC crystal structure. Its atomic weight is 26.98g/mole, and its density is 2.70g/cm3. Determine the atomic radius of a single aluminum atom.

  Determine appropriate vectors and switching times

The balanced 60Hz waveform sample that we must modulate is the point where t=4.4ms. The DC voltage from rail to rail is 300V. assume the q axis and a axis are in same direction. The use of mathCAD is recommended.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd