What is their mortality risk for radon-induced lung cancer

Assignment Help Electrical Engineering
Reference no: EM131005417

1. Consider people who receive an annual radon exposure (EEC basis) of 0.11 MBq h m-3 for the first 30 years of their lives. At age 30, through radon reduction remediation actions, they decrease their annual exposure to 0.02 MBq h m-3 for the remainder of their lives.

(a) What is their mortality risk for radon-induced lung cancer?

(b) If they had not undertaken remedial measures, what would be their radon mortality risk?

2. Estimate how many radon-caused lung cancer deaths there are every year in the U.S. if everyone were exposed to the U.S. residential average radon con­ centration of 1.25 pCi/L 75% of the time. Assume an equilibrium factor of F = 0.5. Assume a population of 250 million. State and justify any other assumptions you make.

Reference no: EM131005417

Questions Cloud

How the right to assemble can be abused by terrorists : Discuss how the right to assemble can be abused by terrorists. Does this create a dilemma for policy makers
Take to other governments when they act badly : Is war only called for when our country is directly threatened by another country, or are there additional reasons to justify taking up arms against another nation? If not, then are there alternative responses our country can take to other government..
Explorative data analysis for series and lead-lag estimation : Principles of Ito calculus and stochastic differential equations - introduction to the Black&Scholes model of option pricing.
Voluntary export restriction : Suppose Japan agreed to a Voluntary Export Restriction (VER) that reduced US imports of Japanese steel by 10%. Discuss what would be the likely short-run effects of that VER on the US and Japanese steel industries. If the restriction were permanent, ..
What is their mortality risk for radon-induced lung cancer : Consider people who receive an annual radon exposure (EEC basis) of 0.11 MBq h m-3 for the first 30 years of their lives. At age 30, through radon reduction remediation actions, they decrease their annual exposure to 0.02 MBq h m-3 for the remaind..
Utility function for an increase in her cash position : Jay Boville Corporation is being sued by Lark Dent. Lark Dent can settle out of court and win $40,000 or go to court. If Lark goes to court, there is a 30% chance that she will win the case. If she wins, a small and a large settlement are equally lik..
Consider the solow model with total factor productivity : Consider the Solow model with total factor productivity At constantly growing at rate g>0. Determine the a) instantaneous impact on GDP per capita, instantaneous impact on consumption per capita, long-run impact on GDP per capita (i.e. compare the le..
What is the annual radon exposure : An individual is exposed 75% of the time to radon with a physical concentration of 4.6 pCi/L and an equilibrium factor of F = 0.6. The remaining 25% of the time, the individual is exposed to radon at a concentration of 1.3 pCi/L and with an equili..
Winn uses straight line depreciation : Prepare the appropriate entries for Winn Heat Transfer from the inception of the lease through the end of 2011. Winn's fiscal year is the calendar year. Winn uses straight-line depreciation.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How can i mix ticl4 and h2o i want to prepare tio2

how can i mix ticl4 and h2o? i want to prepare tio2 nanoparticles. what should be the ratio of ticl4 and water.

  Transpower is asking for anyone with ideas that could delay

transpower is asking for anyone with ideas that could delay the need for new power lines into auckland to come

  Define timing of output changes with ref to input changes

construct a simple SR latch using push-buttons for inputs and l.e.d.s for outputs. Describe the timing of output changes with reference to input changes. ON THE SAME PAGE, construct a simple clocked D-type clocked flip-flop, again using a push but..

  How much reactive power is flowing from bus 1 to 2

The voltage on bus 1 is 1.0 per unit (pu) at 30 degrees; the voltage on bus 2 is 0.95 per unit at 5 degrees. The reactance connecting bus 1 to bus 2 is 0.5 per unit Ohms, and the resistance is negligible. a)How much real power (pu) is flowing from ..

  Compare the worse case time to do an operation with alu

Use the simulation timing diagram to compare the worse case time to do an operation with your ALU with the worst case using the 74LS381. State which operation takes the longest and list the time required for both ALU's.

  What current in amperes will flow through the bulbs

A 100 W bulb takes 0.833A and a 200 W bulb takes 1.67 A from a 120V source. If the two bulb were connected across a 240 V source, what current in amperes will flow through the bulbs?

  Depicts a simplified scheme for cdma encoding and decoding

figure 1 depicts a simplified scheme for cdma encoding and decoding. there are seven logical channelsall using dsss

  Create a circuit using only the basic gates-not-and-nor

A 6-bit answer based on the selected Operation. The error bit is turned on if either no Operation is selected or more than one Operation is selected.

  What will be the step-angle for a hybrid stepper motor

If a stepper motor has a step-angle of 7.5? , what digital input rate is required to produce a rotation of 10 rev/sec What will be the step-angle for a hybrid stepper motor with eight stator windings and ten rotor teeth

  Determine at what speed should the machine be operated

A 450 piece/hr 10 hr B 500 piece/hr 8 hr A set of unsharpen ed tools costs $1,500 and can be ground 15 times. The cost of each grinding is $20. The time required to change and reset the tools is 2 hours, and such changes are made by a tool-setter.

  What is the minimum value of t for reliable data sample

A 10-bit unipolar ADC with a reference of 5.00 F and a 44 micro seconds conversion time will be used to collect data on time constant measurement. Thus, the input will be of the form V (t) = 4(1-e^t/T) . What is the minimum value of T

  How to generate the transmitter level frequency

Frequency multiplers are used at the transmitter to bring up the frequency level to the transmitter level frequency. Why don't we use the crystal oscillator to generate the transmitter level frequency

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd