What is the total rate of heat transfer from a 1 m x 1 m

Assignment Help Mechanical Engineering
Reference no: EM13625113

Circular copper rods of diameter D=1mm and length L=25mm areused to enhance heat transfer from a surface that is maintained atTs,1=100 deg.C. One end of the rod is attached tothis surface (at x=o), hile the other end (at x=25mm) is joined toa second surface that is maintained at Ts,2=0deg.C. Air flowing between the surfaces (and over the rods)is also at a temperature T?= 0 deg. C, and has a convectioncoefficient of h=100 w/m2kelvin.

a. What is the rate of heat transfer by convection from a singlecopper rod to air?

b. What is the total rate of heat transfer from a 1 m x 1 m section of the surface at 100 deg.C, if a bundle of the rods is installed on 4-mm centers?

Reference no: EM13625113

Questions Cloud

The temperature is assumed to vary linearly as a function : a bicyclist leaves from her home at 9 a.m. and rides to a beach 40 mi away. because of a breeze off the ocean the
Regardless of your answer to the last question suppose th : george is curious. he has been told that the average body temperature of humans is 98.6 degrees fahrenheit. however he
According to the national institute for mental health 12 : according to the national institute for mental health 12 of women is affected by depressive disorder each year. suppose
A find the change in classiclal momentumof an electron that : a find the change in classiclal momentumof an electron that accelerates from 0.900c to 0.940c neglecting relativistic
What is the total rate of heat transfer from a 1 m x 1 m : circular copper rods of diameter d1mm and length l25mm areused to enhance heat transfer from a surface that is
To determine the efficiency of the current ticket operation : mike dreskin manages a large los angeles movie theater complex called cinema l ll lll lv. each of the four auditoriums
A piston-cylinder assembly with initial volume of 80 liters : a piston-cylinder assembly with initial volume of 80 liters contains 4 kg of r-134a at a pressure of 160 kpa state 1.
The altimeter on a low-speed piper aztec reads 8000 ft a : the altimeter on a low-speed piper aztec reads 8000 ft. a pitot tube mounted on the wing tip measures a pressure of
The specific internal energy decreases by 5 kj per kg and : an object with a mass of 5 kg undergoes a process during which there is heat transfer from the object at a rate of 5 kj

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the final pressure and volume of the system

The process and volume relation is given p=(8-4v)bar for a non flow process ,where V is in cubic meter.If 130kJ of work is supplied to the system,calculate the final pressure and volume of the system.Take the initial volume as 0.5 cubic meter.

  The specific gravity of solids is 270 determine the

a soil sample has a total unit weight of 16.97 knm3 and a void ratio of 0.84. the specific gravity of solids is 2.70.

  What is the resistance of the wire

The magnetic flux that passes through one turn of a 12-turn coil of wire changes to 4.0 from 9.0 Wb in a time of 0.050 s. The average induced current in the coil is 230 A. What is the resistance of the wire?

  If the elevation points a and b relative to the elevation

a contractor is required to prepare a soil surface so that its planar and the normal direction to the surface is within

  In figure below a charged particle moves into a region of

in figure below a charged particle moves into a region of uniform magnetic field goes through half a circle and then

  There is a heat-pump that takes water from one side of the

a 630000 gallon tank sits empty outside where the temperature is 20 degrees f. the tank is then immediately filled

  Find the required length of the pipe if the bulk outlet

a thin-walled pipe of d 20 mm internal diameter is subjected to a constant heat flow on the surface of strength q400 w

  The outisde tempature drops to -27 celsius determine the

a heat pump is to be used to heat a building during the winter. the building is to be maintained at 24.2 celsiius at

  Under what conditions is the maximum achieved

A steam turbine is operated ith an input temp of 800C and exhaust temp of 150C. What is the maximum amount of work the turbine can do for a given heat input Q? Under what conditions is the maximum achieved?

  Air undergoes a isentropic compression in a piston-cylinder

air undergoes a isentropic compression in a piston-cylinder assembly from p1- 1atm t1 70 f to p2 5 atm. assuming air

  The question to address is what have you learned about

the final paper provides you with an opportunity to integrate and reflect on what you have learned during the class.the

  Determine temperature at which the water starts boiling

A cooking pot whose inner diameter is 20 cm is filled with water and covered with a 4-kg lid. If the local atmospheric pressure is 101 kPa, determine the temperature at which the water starts boiling when it is heated.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd