What is the theoretical highest bit rate transmission

Assignment Help Electrical Engineering
Reference no: EM13167444

Task 1 

Determine the bandwidth and expected information capacity of typical communication systems

Q1

(a) Describe the main factors upon which the maximum data rate over a channel depends.

(b) State the  Nyquist Theorem and the Shannon Theorem for data channel capacity and explain the main difference between them.

(i) A telephone line has a bandwidth of 3000Hz. (300-3300Hz). The signal to noise ratio (SNR) is 35dB.

What is the theoretical highest bit rate transmission over the line?

(ii) A channel has a 1 MHz bandwidth. The SNR for this channel is 63dB.

What is the appropriate bit rate and number of signal levels?

Discuss the various channel impairments and theirresultant effect on the maximum system bit rate fordigital systems

 Q2

There are several impairments in every channel besides those incorporated into Shannon's Law. Discuss these and the effects they may have on the channel capacity.

 Task 2 

Explain the need for modulation and the variety ofmodulation schemes used for analogue

Q3

(a) Discuss why radio frequency waves need a carrier wave for transmission. Expand your answer to develop mathematical expressions for

(i) An amplitude modulated wave

(ii) A frequency modulated wave

(b)  An AM wave is represented by the expression :

v = 5 (1 + 0.6 cos 6280 t) sin 211 × 104 t volts

(i) What are the minimum and maximum amplitudes of the AM wave ?

(ii) What frequency components are contained in the modulated wave and what is the amplitude of each component?

Discuss the modulation methods used to representdigital data over analogue networks

 Q4

Explain what you understand by the terms ;

 (i)   amplitude shift keying (ASK),

 (ii)  frequency shift keying (FSK),

 (iii)  phase shift keying (PSK),

Illustrate your answer in each case by considering a carrier wave being modulated by the following waveform;

1116_Information capacity of typical communication systems.png

Describe the range of digital modulation methods and typical applications

Q5

Various methods can be used to modulate pulse trains by analogue signals. Explain briefly the techniques used.

Describe, with the aid of diagrams, how

(i) Pulse Amplitude Modulation (PAM) and

(ii) Pulse Width Modulation (PWM) is achieved

Discuss the spectrum of each and how the modulating signal can be recovered.

Explain the reasons for multiplexing signals givingexamples of the methods used

Q6

Explain the term 'multiplexing' in general and describe why it is particularly important in the transmission of PAM signals.

Five different modulating signals are to be transmitted efficiently using PAM. Show how this can be achieved using time division multiplexing (TDM).

Your answer should contain  a sketch of the system configuration and a waveform diagram showing how the sampled signals are time sequenced.

Task 3

Evaluate the nature of telecommunications traffic carried over circuit switched networks

Evaluate the nature of telecommunications traffic carried over packet switched networks

Q7

Describe what is meant by;

(a) a circuit switched network

(b)  a packet switched network

Illustrate your answer with diagrams  and  highlight the advantages and disadvantages of each.

Discuss the type or nature of telecommunications traffic which is carried over each network

Apply mathematical formulae to typical examples oftelecommunications traffic

Q8

(a) What do you understand by the terms;

(i) Erlang

(ii) Grade of Service (GOS)

(iii) Busy Hour Traffic (BHT)

(b)  How many lines are required in a particular  trunk group if 2 calls being blocked in every 100 calls attempted is tolerated  and the Busy Hour Traffic is 10 Erlangs,

(c) What percentage of calls will be answered within 20 seconds if a call centre receives 650 calls in an hour of average duration 150 seconds and is manned with 34 available agents?

Reference no: EM13167444

Questions Cloud

Calculate the change in enthalpy delta h : Calculate the change in enthalpy, Delta H. Report your answer in Joules.
How many kilojoules of heat were absorbed : An ice bag containing 324 of ice at 0deg C was used to treat sore muscles. When the bag was removed, the ice had melted and the liquid water had a temperature of 17.0 deg C.How many kilojoules of heat were absorbed?
Analyse the result in terms of the original research : Interpret and analyse the result in terms of the original research specification Make recommendations and justify areas for further consideration.
What is the balanced equation for the combustion : What is the balanced equation for the combustion of 1-naphthol, C10H7OH, to give CO2 and H2O? Do not include phases.
What is the theoretical highest bit rate transmission : Explain the term 'multiplexing' in general and describe why it is particularly important in the transmission of PAM signals and describe the main factors upon which the maximum data rate over a channel depends.
State acetic acid and potassium hydroxide are combined : Write a net ionic equation for the reaction that occurs when aqueous solutions of acetic acid and potassium hydroxide are combined.
What is the weight of nacl formed : An excess of NaOH is treated with 1.1L of dry HCl gas (measured at STP). What is the weight of NaCl formed?
What percent of the acid is dissociated : If the acid dissociation constant, Ksuba, for an acid HA is 8 x 10^-4 at 25 degree C, what percent of the acid is dissociated in a 0.50 M solution of HA at 25 degree C?
Explain what is a trans fat : What is a trans fat? Why would partially hydrogenated oils contain higher amounts of trans fats than natural fats and oils? Why are saturated and trans fats considered a risk factor for cardiovascular disease?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Transactive memory system

What are some of the possible biases and points of error that may arise in team communication systems and what are the advantages and disadvantages of a transactive memory system (TMS) in a team

  Approximation of quarter circle using bezier curve

Approximation of quarter circle using Bezier curve, Determine the Bezier curve of order 3 that approximates a quarter circle centered at (0,0), (1,0), (0,1).

  Ziegler-nichols open loop tuning

Ziegler-Nichols Open Loop Tuning Often, when working with a faster loop, many people will opt only for a PI control philosophy

  Shielding effectiveness with copper also steel at equality

Shielding Effectiveness with copper and steel at equality, Determine the frequency at which two 1 mm thick shields, one made of copper and the other of steel

  Explain a first-order circuit

A first-order circuit, having a gain of 10 at dc and a gain of 1 at infinite frequency, has its pole at 20 kHz. Find its transfer function.

  The design must show all stages used in its development

The design must show all stages used in its development and must be implemented and tested in PSpice and suitable timing waveforms produced.

  Create the walsh code matrix for a w

Create the Walsh code matrix for a W16. (c) For IS-95, on the forward link, list the Walsh code assigned to the various logical channels (hint: there are 64 Walsh codes)

  Explain half-wave rectifier

Half-Wave Rectifier, For the half-wave rectifier, the source is a sinusoid of 120 Vrms at a frequency of 60 Hz. The load resistor is 5 ohms. Determine

  Give description of transformer

Description of Transformer, An 11 kV to 415 V transformer has a rating of 100 kVA. The winding resistance and leakage reactance when referred to the secondary are 0.0142 Ohm and 0.0569 Ohm respectively

  Explain radio systems

Radio Systems, In design of radio systems that incorporate wireless networks, considerations must be taken such as user access, transmission direction, switching and signal strength.

  Why can''t a video signal such as an ntsc analog television

Why can't a video signal such as an NTSC analog television signal be transmitted over a two km length of loaded twisted pair cable with a frequency range 300 Hz to 3,400 Hz? What is the bandwidth occupied by an NTSC video signal?

  Explain the atsc broadcast television system

The ATSC broadcast television system used in the US transmits video signals at an average rate of 18.34 Mbps and employs 8-VSB modulation.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd