What is the smallest number of bits the adc needs to have

Assignment Help Electrical Engineering
Reference no: EM13285257

Design the circuit that interfaces a 2.5V 1mA LED to YourComputer.

If a system uses a 12-bit ADC, about how many decimal digits will it have?

If a system requires decimal digits of precision, what is the smallest number of bits the ADC needs to have?

Reference no: EM13285257

Questions Cloud

Prepare a loan amortization schedule showing the interest : Loan amortization schedule Joan Messineo borrowed $15,000 at a 14% annual rate of interest to be repaid over 3 years. The loan is amortized into three equal, annual, end-of-year payments.
What might be the outcome of a utilitarian analysis : Susan serves on the city building commission.  The city is planning to build a new subway system to extend the reach of the subway further out from the city center.  Susan’s cousin, Sam, owns Subway Mobility Co., submitted the lowest bid for the syst..
Calculate the divergence in cylindrical coordinates : For the vector field Eˆ=5exp(-2r)rˆ-3rzˆ calculate the divergence in cylindrical coordinates. Verify the divergence theorem for the cylindrical region enclosed by r=2, z=0 to 4.
State and write the balanced complete ionic equations : Write the balanced complete ionic equations and net ionic equations for the reactions that occur when each of the following solutions are mixed. AgNO3(aq) and K2SO4(aq)
What is the smallest number of bits the adc needs to have : Design the circuit that interfaces a 2.5V 1mA LED to YourComputer. If a system uses a 12-bit ADC, about how many decimal digits will it have If a system requires decimal digits of precision, what is the smallest number of bits the ADC needs to have
Depict the structure of the one alkene : Draw the structure of the one alkene which upon treatment with O2 followed by Zn and acid, would give rise to formaldehyde and cyclohexanone
Find the complex power of the other load of source : Two loads connected in parallel are supplied from a single-phase 240-V rms source. The two loads draw a total real power of 400kw at a power factor 0f 0.8 lagging. One of the loads draws 120kW at a power factor of 0.96 leading. Find the complex po..
What is the value of a put option written on the stock : What is the value of a put option written on the stock with the same strike price and expiration date as the call option?
What is the nal of the lease : The machine has an estimated residual value of $250,000 at the end of the 4th year.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine how far backed-off must the amplifier operate

If the SNR must be greater than 40 dBm, how far backed-off must the amplifier operate. Assume noise comes from a third-order intermodulation between two interferers with the same power level as the wanted signal.

  Connect a voltage divider to an output of a dc power supply

Design it to give an output that is 1/3 of the supply voltage. Furthermore neither the power ratings of the resistors nor the current rating of the supply are to be exceeded. The voltage output of the divider much not change by more than 1% when l..

  What is the snr that could be tolerated without error

If the data stream is transmitted using a bandwidth of 64 kHz in an ordinary system (without spread spectrum), what is the SNR that could be tolerated without experiencing significant errors

  How to sketch the fourier transform of the sampled signal

An input signal x(t) = cosωct is sampled by an ideal sampling function with ωs= 1.5 ωc. The sampled signal is then filtered with an ideal low pass filter H(ω)= rect(ω/1,5ωc) to form an output signal y(t) a. Sketch the fourier transform of the sampl..

  What is the magnitude of the instantaneous current at 20usec

A charged 100- picoFarad capacitor has initial voltage across it of 10 V. A 100 kohm resistor is suddenly connected across the capacitor (at t=0) to discharge it. What is the magnitude of the instantaneous current at 20 usec

  Determine the reflection and transmission coefficients

i. Find the refractive index of the dielectric medium. ii. At what angle of incidence will the incident TM wave be totally refracted into air. iii. For a TE wave incident at the angle of incidence found in part (ii) above.

  Determine slip at which the motor develops maximum torque

Use Matlab to verify the above results and determine: a. The starting torque b. The maximum torque c. The slip at which the motor develops maximum torque d. Draw the torque-speed characteristic of the motor

  Determine nyquist sampling rate such that no aliasing occurs

The sampled signal x[n] obtained above is processed by the ideal D-to-C converters with the sampling rate (600 Hz). Obtain the representation of the continuous signal. Determine the Nyquist sampling rate such that no aliasing occurs in the sampled..

  Does the transition depend on the size or shape of the grid

The general belief is that the system exhibits a sharp phase transition from free flowing to fully jammed, as a function of initial density of cars. The existence of this sharp transition has been cited in the scientific literature several hundred..

  What are the factors on which the width depends

Space charge region how it is formed and what are the factors on which the width of this region depends

  What is the probability that the lowest number drawn is k

An urn contains N balls numbered 1 to N. Someone draws n balls(without replacement) from the urn, where 1

  Design a decade up counter using jk flip flops

Design a decade up counter using JK flip flops. THe conter should count from 0 to 9 and back to 0, etc. Include a "COUNT" input to control the counter. THe counter will advance only if the COUNT = 1.Also include a "CARRY OUT" output.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd