What is the slope of the channel

Assignment Help Mechanical Engineering
Reference no: EM13935951

1. A surveyor finds that the bottom of a rectangular channel drops 3.75 feet in a distance of 200.0 feet. What is the slope of the channel?

2. The bottom elevation of a trapezoidal channel is 422.05 at station 1100 and 423.92 at station 1150. What is the slope of the channel?

Reference no: EM13935951

Questions Cloud

Difference between twitter and instant messaging : Question 1: What is the difference between Twitter and Instant Messaging? Question 2: List and briefly discuss three
What is the cross-sectional area of the flow : What is the cross-sectional area of the flow and what is the wetted perimeter and what is the hydraulic radius?
Explain the steps that would reflect triangular arbitrage : Given this information, is triangular arbitrage possible? If so, explain the steps that would reflect triangular arbitrage, and compute the profit from this strategy if you had £1 000 000 to invest.
Apply the requirements and architecture models : Apply the Requirements and Architecture Models to perform the analysis and design of the alarm control software described above (you can make - and should document - necessary assumptions), and document all results obtained from each of the follow..
What is the slope of the channel : 1. A surveyor finds that the bottom of a rectangular channel drops 3.75 feet in a distance of 200.0 feet. What is the slope of the channel?
Write brief introduction of the given article : Article- Comparing Public-Versus-Private Sector Pay and Benefits: Examining Lifetime Compensation by Thom Reilly. Read the Article and write a 4 page minimum article critique following the below outline in APA Site
Evaluate both infix and postfix expressions : You are to extend the calculator so that it gives the user the option of entering expressions in infix notation or postfix notation (a.k.a. Reverse Polish notation). In order to accomplish this, you will need to perform the following tasks:
Describe the elements of humoral and cellular immunity : Describe the elements of humoral and cellular immunity that are involved in immune responses to viral infections. What mechanisms have infectious agents evolved to defeat these elements?
Describe lytic and lysogenic life cycles of a bacteriphages : Describe the lytic and lysogenic life cycles of a bacteriphages. Include in your answer comparisons and contrasts between the 2 types of cycles.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine displacement of in diameter steel bar

Determine displacement (in) of a 1.08 in diameter steel bar, which is 834 ft long under a force of 33,222 lb if elasticity modulus is 30 x 106 psi. Make sure you do not round up your answer to less than 4 significant (non-zero) figures.

  Isolated system consists of a closed copper vessel of mass

An isolated system consists of a closed copper vessel of mass 0.1 kg, containing 1 kg of liquid water, each initially at 5°C, immersed in 20 kg of liquid water, initially at 20°C. The system is allowed to come to equilibrium. Determine the final temp..

  What should be the minimum horsepower of the lathe

A 3 in. diameter low strength, stainless steel cylindrical part is to be turned on a lathe at six hundred rpm. With a depth of cut of .3 inches and a feed of .025 in/rev. what should be the minimum horsepower of the lathe?

  Compute the stress in the bar and the resulting design

a steady tensile load of 5.00kn is applied to a square bar 12mm on a side and having a length of 1.65m. compute the

  Determine the maximum allowable tensile force on the bar if

a structural lin that is 3 in. wide and 0.5 in. thick is to have a factor of safety of 2 relative to its yield strength

  Ten kilograms of ice at 260 k is dumped into 20 kg of

ten kilograms of ice at 260 k is dumped into 20 kg of liquid water initially at 300 k in an insulated container. the

  An aluminum rod is made in the form of a hollow square tube

an aluminum rod is made in the form of a hollow square tube 2.25 in outside with a wall thickness of .120 in. its

  Determine the torque exerted on the 10mm long high inner

whole blood is placed in a concentric cylindern viscometer. the gap width is 1 mm and the inner cylinder radius is 30

  If the friction mep is 122 bar in both cases determine the

a certain generating power plant requires 1 mw output. two types of diesel- engine installations are available. one

  Bolts are tested in batches or lots a specified number are

you are a manufacturing engineer working for an aircraft company. the production lines you are responsible for are

  Describe the three parts sensortransducer signal

describe the three parts sensortransducer signal conditioning output stage of the following measurement systems

  Cold air-standard brayton refrigeration cycle

A cold air-standard Brayton refrigeration cycle has a pressure ratio of 4 and a refrigeration rate of 15 kW. Air enters the compressor at -7oC. The high pressure air is cooled to 27 oC by rejecting heat to the surroundings. It is further cooled to -1..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd