User Account

All Pages

What is the safety factor if the fillet radius is 1 mm

Assignment Help Mechanical Engineering
Reference no: EM131307188

The stepped shaft rotates at 120 rpm and has a 20 kW input at A. 16 kW is taken off to operate machinery at B, and the remaining 4 kW is used at C. The shaft is stainless steel with yield strength in shear of 300 MPa.

a. Not including the effect of stress-concentration, what are the minimum allowable diameters for segments AB and BC to achieve a safety factor of 3?

b. With the minimum shaft radii, and now considering stress-concentration, what is the safety factor if the fillet radius is 1 mm?

928_86d8762b-45a5-41ba-9245-d5b968df9522.png

Reference no: EM131307188

Questions Cloud

Discuss about the prejudice and discrimination : Discuss about the prejudice and discrimination,stereotyping, glass ceiling,, bias, discrimination, give example for each one.
Determine the ratio of weights for the two shafts : what must be the thickness of the tube for the same linearly elastic material working at the same maximum stress? Determine the ratio of weights for the two shafts.
How nature vs nature impacts child development has ongoing : Watch the videos from McDowell and Pollack. The debate regarding nature versus nurture and how it impacts child development has been ongoing for centuries.
What is the resulting maximum shear stress : The propeller of a wind generator is supported by a hollow circular shaft with 0.4 m outer radius and 0.3 m inner radius. The shear modulus of the material is G = 80 GPa.
What is the safety factor if the fillet radius is 1 mm : Not including the effect of stress-concentration, what are the minimum allowable diameters for segments AB and BC to achieve a safety factor of 3?
Calculate the profitability index for a project : Calculate the profitability index (PI) for a project whose present cash flow value is $500,000 with an initial investment of $430,000.
Construct depreciation table using the straight line method : A machine has a value of $65,000 and is estimated to operate up to 6 years, ending with a scrap value of $7,000. Construct a depreciation table using the straight-line method.
Do inmates give up all rights when they enter prison : Do inmates give up all rights when they enter prison? Does this include the right to practice their religion? Does this apply to all prisoners, or just to Native Americans?
How long will it take for equipment valued : How long will it take for equipment valued at $35,000 to depreciate to less than half of its original value if it normally depreciates to $5,000 in 14 years? Use the fixed-proportion method.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compute the equations of streamlines that pass through xy

for the two-dimensional flow with velocity components u y - 2 and v 2x3i compute the equations of

  Determine the range of weights

Compute the force P required to slide the door at a steady speed if wheel A becomes "frozen" and does not turn in its bearing.

  When will the annual expenditures reach one trillion dollars

Find an exponential regression model for the data. Estimate (to the nearest billion) the annual expenditures in 2017.

  Determine the wet-bulb temperature of the air

Determine the wet-bulb temperature of the air. Express your answer in degrees Celsius to four significant figures.

  Gauge pressure at the oil-water interface

A barrel contains a 0.120-m layer of oil floating on water that is 0.250 m deep. The density of the oil is 600 kg/m.

  Determine all of the state points and the efficiency what

in an air-standard brayton cycle air enters the compressor at 1000 lbmhr 14.7 psia and 40degf and exits at 70 psig. the

  Decentralized and semicentralized peer-to-peer architectures

Give two advantages and two disadvantages of decentralized and semicentralized peer-to-peer architectures.

  Brake power and indicated power of a petrol engine

The difference between the brake power and indicated power of a petrol engine and a diesel engine

  If we remove both the forces of drag and buoyancy the

trees at the bottom of a lake are approximated as a truncated cone with a base diameter of 6 ft a top diameter of 1 ft

  The enthalpies of entering and exiting fluid are 27912 kjkg

a system receives 0.756 kgs of a fluid at a velocity of 36.58 ms at an elevation of 30.48 m. at the exit at an

  In a refrigerator cycle low saturated liquid enters an

in a refrigerator cycle low saturated liquid enters an evaporator and exits as saturated vapor. the saturated vapor is

  Probable cause of discrepancy

Strains measured as the bar was pulled in tension were used to compute Young's modulus. Readings from one gauge gave a modulus much higher than those from the other gauge. What was the probable cause of this discrepancy?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd