What is the resulting brake torque

Assignment Help Mechanical Engineering
Reference no: EM131378711

Estimate the brake torque in Problem 18.24 using long-shoe equations.

Problem 18.24

Figure P18.24 shows a brake with one shoe (a second shoe would normally be used to balance the forces, but only one shoe is shown here to keep the problem short). The width of shoe contact with the drum is 40 mm. The friction material provides a coefficient of friction of 0.3, and permits an average pressure of 600 kPa, based on the projected area of contact. Use the short-shoe approximate relationships. The initial drum speed is 1200 rpm.

(a) What value of force F can be applied without exceeding the allowable contact pressure?

(b) What is the resulting brake torque?

(c) Is the brake self-energizing or deenergizing for the direction of rotation?

(d) What radial force is applied to the pivot bearing at point A?

(e) If full application of the brake brings the drum from 240 rpm to a stop in 6 seconds, how much heat is generated?

(f) What is the average power developed by the brake during the stop?

934_33b4849e-8a4f-4c0b-8f65-c757e5c17cbc.png

Reference no: EM131378711

Questions Cloud

Was young correct in given case : When Sorrell discovered the landfill, he sued Young and asked the court to rescind the agreement. Young claimed he was under no obligation to reveal the fill to Sorrell. Was Young correct? Explain.
Was beachcomber correct in given situation : Beachcomber sued Boskett for rescission and a return of the $500. Beachcomber claimed this bilateral mistake of fact created grounds for a rescission. Was Beachcomber correct? Explain.
On what legal grounds could the warden refuse : He also received 180 days of administrative segregation and the loss of 1,283 days of goodtime earned. On what legal grounds could the warden refuse to keep his promise to the inmates? Explain.
What influence did later civilizations have on these areas : What factors enabled civilization to appear first in Mesopotamia and then second in Egypt? What influence did later civilizations have on these areas
What is the resulting brake torque : Use the short-shoe approximate relationships. The initial drum speed is 1200 rpm.
Did the court grant lorals request : After delivering the radar sets, Loral sued Austin and asked the court to rescind the price increase. Did the court grant Loral's request? Explain.
How would you predict the court will rule in given case : How would you predict the court will rule in this case? Did the nephew give up enough under the law, or is his promise to Uncle William a cleverly constructed illusion?
What was the name of the atomic bomb : What was the name of the atomic bomb that was dropped on Nagasaki by Ammerica during World War II
Find common rhetorical strategies : WRTG 3012: Writing in the Social Sciences Find common rhetorical strategies (*SPECIFIC ways ethos, pathos and logos are constructed) and discuss specifically how different pieces are using these strategies similarly or differently

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd