What is the resistance at 20 ms

Assignment Help Electrical Engineering
Reference no: EM131392893

Suppose there is another 20-ms light pulse that may strike the cell in given Problem, but it is of lower intensity, so that the final resistance would be . Call this one and that of Problem P2. Devise a system that will latch on a red LED if strikes the cell, or a green LED if strikes the cell. Each time a pulse strikes the cell, the latches are cleared and the appropriate LED turned on.

Problem
A CdS cell has a time constant of 73 ms and a dark resistance of 150 kΩ. A light pulse that is only 20 ms in length strikes the cell. If the intensity of the light pulse is such that the final resistance would be , plot the resistance versus time for 100 ms. What is the resistance at 20 ms?

Reference no: EM131392893

Questions Cloud

Foundational concepts and principles of microeconomics : Over the past seven weeks, we have explored the foundational concepts and principles of microeconomics, and we have applied them to the world around us. Choose one microeconomic concept applied in your final project. Explain your findings and the imp..
Write the steps of gourand interpolation shading technique : Write the steps of Gourand interpolation shading technique. A cubic Bezier curve is to be drawn given the control points P1 (40, 40), P2 (10, 40), P3 (60, 60), P4 (60, 0). Calculate the coordinates of the points on the curve at t= 0.2, 0, 4 and 0.6
Determine and plot the average power delivered : Determine and plot the average power delivered to a 100-Ω load in place of the light bulb in Example as a function of resistor R.
Good governance is of both global and universal concern : A number of writers on governance have observed that good governance is of both global and universal concern; Using the example of a company you are familiar with what do you see as effective indicators and measures for assessing various aspects of g..
What is the resistance at 20 ms : If the intensity of the light pulse is such that the final resistance would be , plot the resistance versus time for 100 ms. What is the resistance at 20 ms?
Discuss about the quantitative data analysis : Understanding the use of basic statistical strategies is part of being a critical consumer of published research literature. Unless they plan to conduct research themselves, it is not as important for counselors to understand the mathematical calc..
Find the profits earned from the price strategy : A firm charges its customers $20/unit for the first unit purchased and $10 for each additional unit in excess of one unit. Suppose the firm’s marginal cost is fixed at $5. How many units will this firm sell? Find the profits earned from the price str..
Having recently been made redundant : David Raines is an experienced senior manager who wants to create a business that would employ him and provide for his family when he chose to retire. He also feels the pull of building his own enterprise and in turn wants to help others in his rural..
Plot the voltages across the capacitor : What is the range of R to provide 5% to 95% on time of the SCR?- Plot the voltages across the capacitor, load, and SCR for a 50% on time.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine what is the nominal resistance of the resistor

the color code on a resistor specifies the resistance as4.7kOhms. A multimeter measured the resistance as 4.688kOhms. What is the nominal resistance of the resistor

  At what rate must analog signal from a microphone be sampled

if maximum frequency audible to a human ear is 20,000 Hz, at what rate must the analog signal from a microphone be sampled when converting it to digital

  How many flip flops are needed to build a register file

How many flip flops are needed to build a register file with 32 16-bit registers where register 0 is always 0x0000?

  Find the magnitude of the electric field at given distance

A sphere of radius 100mm has a charge 4 C uniformly distributed throughout its volume. Find the magnitude of the electric field at distance 100.1 mm from the centre of the sphere.

  Calculate the amplitude of the open-circuit phase voltage

Calculate the amplitude (peak value) of the open-circuit phase voltage measured when the rotor is turned at 60 rev/sec.

  Obtain timing diagram for positive-edge-triggered flip flop

Obtain a timing diagram for a positive-edge-triggered JK master-slave flip-flop during four clock pulses. Show the timing diagrams for C, J, K, Q and Q'. Assume that before the first pulse: output Q is equal to 1, J=0 and K=1.

  A wound-rotor induction motor is operating at rated voltage

A wound-rotor induction motor is operating at rated voltage and frequency with its slip rings shorted and with a load of about 25 percent of the rated value for the machine.

  Determine the frequency of oscillation

Given the forward-path transfer function of unity-feedback control systems, apply the RouthHurwitz criterion to determine the stability of the closed-loop system as a function of K, Determine the value or K that will cause sustained constant-ampli..

  Calculate the differential-mode gain

ECE 511: Analog Integrated Circuits Fall 2016 Assignment. Complete the table on the following page related to the operating point for all transistors. This should help in computing the rest of the homework questions. I recommend a spreadsheet for t..

  Design a common emitter amplifier with no bypass capacitor

Design a Common Emitter amplifier with no bypass capacitor which has an overall gain of AV=-15 when the input voltage has a source impedance (Rsource) of 2k, and the amplifier itself has an Rin= 4k, Rload= 6k,VCC= 15V,VBE= 0.7V

  Determine what voltage is actually achieved

Using a 1 mA current source, the designer wishes to create a reference voltage of 1.25 V. Suggest a combination of series and parallel diodes that will do the job as well as possible. How many diodes are needed. What voltage is actually achieved.

  Calculate the energy generated by the electric machine

a. The mass of an electric car is 900 kg including the passengers. A single motor mounted on the front wheels drives the car, and the radius of the wheel is 0.3 m. The car is going downhill at a speed of 50 km/hr, and the slope of the hill is 30 d..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd