What is the readout error when the intensity is given

Assignment Help Electrical Engineering
Reference no: EM13284768

Design a system using the photoconductive cell to measure and display light intensity. Make the design such that 20 to 100 mW/cm2 produces an output of .2 to 1.0 V. What is the readout error when the intensity is 60 mW/cm2?

Reference no: EM13284768

Questions Cloud

What is the present value of the cash flows : If the apporpiate discount rate for the following cash flows is 9 percent compounded quarterly, what is the present value of the cash flows?
Determine the probability for the total series resistance : Two 1 kO resistors are connected in series. Each resistor has 10% tolerance, and the resistance values are statistically independent and uniformly distributed. Determine the probability that the total series resistance of the two resistors is less..
Compute kp and kc for the equilibrium : at 400K and a total pressure of 1.0atm, the mole fraction of H2 is 0.25 and that of I2 is 0.30, in equilibrium with HI. Calculate Kp and Kc for the equilibrium.
Cultural and environmental challenges-multinational firms : The text describes how multinational firms expand and grow through mergers, joint ventures, and alliances. What challenges do HR departments face in realigning their international strategic planning models when such growth occurs? How does the HR dep..
What is the readout error when the intensity is given : Design a system using the photoconductive cell to measure and display light intensity. Make the design such that 20 to 100 mW/cm2 produces an output of .2 to 1.0 V. What is the readout error when the intensity is 60 mW/cm2
Company management and company shareholders : Company management, company shareholders and creditors /lenders. Of these three, which stakeholder do you consider most important and why?
What is the most expensive : What is the most expensive car you could afford if you finance it for 48 months? Round your answer to the nearest cent. What is the most expensive car you could afford if you finance it for 60 months? Round your answer to the nearest cent.
Explain chromium crystalizes forming body center cubic unit : chromium crystalizes forming body center cubic unit cell length 280 pm. What is the radius of chromium atom in pm
What was titans cash coverage ratio for the year : The tax rate was 34 percent. The firm paid $1,940 in total interest expense and deducted $2,730 in depreciation expense. What was Titan's cash coverage ratio for the year?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How does the amplitude setting on function generator relate

With respect to sinusoidal signals, explain the difference between the way we normally define "amplitude" and the "amplitude" measurement on an oscilloscope. Also, How does the amplitude setting on a function generator relate to these

  Calculate built-in potential at each junction in equilibrium

a. Identify which doping level was intended for the emitter, for the base, and for the collector. b. Assuming the intrinsic carrier concentration (ni) in silicon to be 1010cm-3, calculate the Fermi Energy, EF, relative to the intrinsic Fermi energ..

  How to find the voltage in the capacitor vc

if we have a circuit with R= 5, L=22mH, C=22nF , Vs=10 and the switch S was opens for a long time and it closes at time t=0 second. all connected in series, how can i find the voltage in the capacitor Vc

  Explain sketch a block diagram of the arrangement

Sketch a block diagram of the arrangement and calculate suitable values of pad resistance if both the amplifier and the line have a characteristic impedance of 600 Ohm.

  What would the probability become if the temperature rises

For a conductive metal the Fermi energy was determined to be 7.01eV at 300K. a)What is the probability of an electron occupying the energy level of 7.15eV b)What would the probability become if the temperature rises to 757°C

  Calculate the dc resistance in ohms per mile

Three hard-drawn copper conductors with a 1 inch diameter and 1 m spacing in a triangular configuration. (Note that 1 mile = 1.609 km). 1. Calculate the dc resistance in ohms per mile ( p = 1.77 × 10-8-m).

  Calculate the maximum allowable gate drive power

A thyristor is triggered by a pulse of train of 5kHz.The duty ratio of the pulse train are 0.5. If allowable average gate power is 100W, calculate the maximum allowable gate drive power.

  Determine the image frequency and the local oscillator

1-for an FM reciever tuned to 94.5 MHZ using high side-injection and a first IF of 10.7 MHZ, Determine the image frequency and the local oscillator

  How much additional quantity that you have to add

determine the position of fermi level with respect to the valence level. What type of dopant and how much additional quantity that you have to add to this crystal to move the fermi level by (an energy amount of) KT toward the valence band

  Determine the line impedance of thje souece

In a balanced three-phase wye-wye system, the load impedance is 4 + j3 . The source has phase sequence abc and Van = 120

  What is the maximum power that can be delivered to the load

The battery is made by connecting 5 unit cells in series and then by connecting 7 of these series cells in parallel. Each unit cell has the voltage of 1.25 V and the internal resistance if 3.4 Ohm.

  Find what is the highest voltage allowed at the drain

A p-channel MOSFET with a threshold voltage V,p = -0.7 V has its SOUTce connected to ground. (a) What should the gate voltage be for the device to operate with an overdrive voltage of Ilor! = 0.5 V

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd