What is the rate of flow of cooling water through the

Assignment Help Mechanical Engineering
Reference no: EM13611161

Consider an ideal steam cycle that combines the reheat cycle and the generative cycle. The net power output of the turbine is 100,000 kw. Steam enters the high pressure turbine at 1200 psia, 1000 F. After expansion to 90 psia, some of the steam goes to an open feedwater heater and the balance is reheated to 700 F, after which it expands to 1 psia. (b) What is the steady flow rate to the high pressure turbine? (c) What hp motor is required to drive each of the pumps? (d) If there is a 20 F rise in the temperature of the cooling water, what is the rate of flow of cooling water through the condenser? (e) The velocity of the steam flowing from the turbine to the condenser is limited to a maximum 400 ft/sec. What is the diameter of this connecting pipe?

Reference no: EM13611161

Questions Cloud

The ball leaves the club at a speed of 187 ms at an angle : a golfer hits a shot to a green that is elevated 2.70 m above the point where the ball is struck. the ball leaves the
Determine the thermal efficiency of the system assuming : air enters the compressor of a regenerative gas-turbine engine at 300 k and 100 kpa where it is compressed to 800 kpa
Prove that the velocity induced region surrounding a doubly : prove that the velocity induced region surrounding a doubly infinite vortex sheet of constant strength satisfies the
A tennis ball is struck and departs from the racket : a tennis ball is struck and departs from the racket horizontally with a speed of 28.4 ms. the ball hits the court at a
What is the rate of flow of cooling water through the : consider an ideal steam cycle that combines the reheat cycle and the generative cycle. the net power output of the
Awhat assumptions about the population should we be willing : studies show that message therapy has a variety of health benefits a sample of 10 typical one-hour massage therapy
A spacecraft is traveling with a velocity of v0x 6150 ms : a spacecraft is traveling with a velocity of v0x 6150 ms along the x direction. two engines are turned on for a time
Accounting procedures allow a business to evaluate their : accounting procedures allow a business to evaluate their inventory at lifo last in fi rst out or fifo first in first
Mayer instrumentation sold a depreciable asset for cash of : mayer instrumentation sold a depreciable asset for cash of 500000. the original cost of the asset was 1600000. mayer

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Electric power is to be generated by installing a hydraulic

electric power is to be generated by installing a hydraulic turbine-generator at a site 130m below the free surface of

  What is the section lift coefficient

Consider a NACA 0009 airfoil that has a plain flap whose length is 0.2c and which is deflected 25. a. Calculate cl and cmc/4 When the geometric angle of attack is 4 degrees, what is the section lift coefficient? Where is the center of pressure?

  If k 0410-3 ft-1 determine d such that a car driving at

if k 0.410-3 ft-1 determine d such that a car driving at constant speed v0180mph experiences at b an acceleration with

  An engineer is designing a system that requires

an engineer is designing a system that requires transporting .01 m3s of helium at 15degc and 120 kpa. the velocity of

  Assuming that r-134a is an ideal gas what would the

assuming that r-134a is an ideal gas what would the specific volume of r-134a at 40 deg c and 0.06 mpaabsolute? how

  Specify a diameter d using a design factor of nd

xerted on the shaft shown in the figure, which rotates at 1150 rev/min and supports a 10-kip bending force. Use a 1095 HR steel. Specify a diameter d using a design factor of nd = 1.6 for a life of 3 min. The surfaces are machined.

  A truck is traveling at v0 60mph when the driver applies

a truck is traveling at v0 60mph when the driver applies the brakes to come to a stop. the deceleration of the truck

  Is the proposed system sound

let it cool back to the outdoor temperature, pass it through a turbine, and discharge the cold air leaving the turbine into the house. from a thermodynamic point of view, is the proposed system sound?

  An electric moter drivers an axial fan assuming that the

an electric moter drivers an axial fan assuming that the desired air velocity 65degree f existing the fan is 50mph and

  Find the optimal compression ration in terms of the upper

it is fair to assume that the heat rejection from an otto cycle is typically to the ambient at a temperature tmin the

  What should the diameter of the nozzle outlet be

What should the diameter of the nozzle outlet be in inches and what is the mass flow rate of steam through the nozzle in lbm/min?

  What should the bungee cord''s relaxed length

As shown, a 130 lb bungee jumper wants to jump from the top of a 655 ft high bridge and be able to just touch the water below. Given that the bungee cord has a spring constant of 2.33 lb/ft, what should the bungee cord's relaxed length, l, be for ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd