What is the propeller rotation rate in rpm what is the

Assignment Help Mechanical Engineering
Reference no: EM13611655

A wind turbine of the 3-bladed propeller type, having 50% efficiency, generates 2 MWe when the wind speed is 14 m/s. The air density is 1.2 kg/m3. Under these conditions, the linear speed of the blade tips is 98 m/s. What is the propeller rotation rate in rpm? What is the propeller shaft torque? What is the torque if the turbine above has two instead of three blades?

Reference no: EM13611655

Questions Cloud

If in reality 54 of the residents oppose building the : a community vote is being held to see if a factory will be built in the community. a survey firm randomly surveyed 180
An iron wire has a cross-sectional area of 101 x 10-5 m2 : an iron wire has a cross-sectional area of 1.01 x 10-5 m2. carry out steps a through e to compute the drift speed of
Shown below are rental and leasing revenue figures for : shown below are rental and leasing revenue figures for office machinery and equipment in the united states over a
On september 30 2013 sternberg company sold office : on september 30 2013 sternberg company sold office equiptment for 12000. the equiptment was purchased on march 31 2010
What is the propeller rotation rate in rpm what is the : a wind turbine of the 3-bladed propeller type having 50 efficiency generates 2 mwe when the wind speed is 14 ms. the
Tyco is a conglomerate organization that had 36 billion : tyco is a conglomerate organization that had 36 billion inrevenue. in a court trial it was alleged that the ceo of
A proton is located at the origin and a second proton is : a proton is located at the origin and a second proton is located on the x-axis at x 6.18 fm 1 fm 10-15 m.a calculate
Calculate the change that occurred in cash during the month : calculate the change that occurred in cash during the month. you may assume that the change in each balance sheet
Use the following data to construct a scatter graph and : investment analysts generally believe the interest rate on bonds is inversely related to the prime interest rate for

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The electric potential at a is -605 v and the electric

a moving particle encounters an external electric field that decreases its kinetic energy from 8830 ev to 7750 ev as

  Determine the magnitude t of applied torque

the tank has a 180mm diameter and 12 mm wall thickness. knowing that the tank contains compressed air under a pressure of 8 Mpa, determine the magnitude t of applied torque for which the maximum normal stress in tank is 75 Mpa.

  What is the first step to solve for an unknown

If we have |N|(en) + F - W = 0 Where The unit vector of N is give, F components unknown and W is only -3400 j. What is the first step to solve for an unknown.

  The can diameter and height are d 65 mm and h 120 mm the

a partially full can of soft drink is placed at the outer edge of a childs merry-go-round located r 1.5 m from the

  What is the speed of the pump

The system on site is a pressure sand filter, with a service curve. The filter is backwashed using the feed pump, at a higher flow rate, shown as backwash curve.  What is the speed of the pump to achieve the service and backwash flow rates ?

  The cylinder from a supply line until all the liquid in the

an insulated vertical piston-cylinder device initially contains 11.56 kg of water 6.94 kg of which is in vapor phase.

  What is the increase in internal energy in ft-lbf taking

1.7 lbm object falling at 162 fts enters a viscous liquid and is essentially brought to rest before it strikes the

  Consider a mass going through a polytropic process where

consider a mass going through a polytropic process where pressure is directly proportional to volume n-1 the process

  Calculate the incidence it of the tailplane for trim if the

calculate the incidence it of the tailplane for trim if the elevator deflection e is zero. ii calculate the neutral

  Draw the front view - third angle projection

Partial Auxiliary View showing the details of the inclined face - supply dimensions for the inclined face only. Select a suitable scale to make the drawing fit on an A3 drawing sheet.

  What type of feedback data should we be collecting

what type of feedback data should we be collecting; in order to make sure that our MPS data, our MRP data, our Aggregate Planning, etc. are all correct?

  Evaluate the heat and work for each process

one kg of execute a carnot power cycle. during the isothermal expansion, the water is heated until is is a saturated vapor the pressure is and the quality is. evaluate the heat and work for each process.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd