What is the pressure in the tank

Assignment Help Mechanical Engineering
Reference no: EM13217021

If 300 Kg of air is pumped into a previously empty 100 m^3 tank, and the temperature of the air in the tank is 25 deg C, then what is the pressure in the tank in N/m^2?

Reference no: EM13217021

Questions Cloud

Explain how has technology impacted the verbal cues : How has technology impacted the verbal and nonverbal cues used in interpreting messages? Provide examples to support your position. Use at least one resource to support your key points.
What is the diameter of the larger piston : a hydraulic system has a mechanical advantage of 4. If a smaller piston has a diameter of 5 inches what is the diameter of the larger piston?
The existence of a hazard-the hazard must be recognized : Describe and discuss how OSHA makes use of Section 5(a)(1) of the Act (commonly referred to as the general duty clause). The existence of a hazard,  The hazard must be recognized,
What are the tensions in cables ef and eg : The system shown anchors a stanchion of cable-suspended roof. If the tension in cable AB is 900 kN, what are the tensions in cables EF and EG?
What is the pressure in the tank : If 300 Kg of air is pumped into a previously empty 100 m^3 tank, and the temperature of the air in the tank is 25 deg C, then what is the pressure in the tank in N/m^2?
Explain what is the breakeven point for the new process : What is the breakeven point for this new process? Compare this process to the process proposed in the previous problem. For what volume of demand should Patricia choose this process?
Sketch hoop and radial stresses in the wall of cylinder : the cylinder is made from steel where yield stress= 240 MPa and v=0.3. Subsequently sketch the hoop and radial stresses in the wall of the cylinder.
Multi-employer worksite policy : Describe and discuss OSHA’s multi-employer worksite policy with regards to employers who control a given worksite, employers whose employees are exposed to a hazard, and employers who create a given hazard.
Concepts from the strategic management : A ppt consisting of 5 slides 4 points per slide and a memo elaborating on the slides for the memo - Should be based on concepts from the strategic management textbook by Dess Lumpkin Eisner and McNamara.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Explain load that can be lifted by aerostat balloon

Load that can be lifted by aerostat balloon An aerostat balloon is filled with hydrogen. It has a volume of 1000m^3 at constant air temperature of 27 degree C and pressure of 0.98bar.

  Determine the rate of heat loss from the molten salt

Determine the rate of heat loss from the molten salt per meter length of the pipe.

  Overall heat transfer coefficient

Explain what is meant by an overall heat transfer coefficient and explain what is mean by failing and what its effect will be on the value of the overall heat transfer coefficient.

  Calculate real gas pseudopressure at a pressure

Calculate real gas pseudopressure at a pressure of 1902.7 psia using the following data and a base pressure of 102.7 psia. Was the calculation of real gas pseudopressure necessary for this gas? Explain your answer.

  Find out the largest couple that can be applied

Determining the largest couple that can be applied to a beam in pure bending. A beam of cross section shown is extruded from an aluminum alloy for which σy = 310 MPa and σu = 480 MPa.

  Explain a car and a high speed trian at constant speeds

A car and a high -speed trian at constant speeds. three seconds after the train passes under the highway bridge the car crosses the bridge.

  What percentage of washers are discarded

25 washers have a combined mass of 1 lb. how much money is recovered per day from the sale of scrap washers?

  Explain motor coming to rest

Motor coming to rest, A motor is running at 12 rpm and the switch is flipped and cuts the power. The rotor weighs 75 lbs.

  What would happen if the air filter was partially choked

What would happen if the air filter was partially choked. If the piston rings were leaking state what you would expect the results of a, b, c, and d above would be.

  Determine the electric flux through this surface

A uniform linear charge density of 4 nC/m is distributed along the entire x axis. Consider a spherical (radius = 5 cm) surface centered on the origin. Determine the electric flux through this surface.

  Determine the engine block surface temperature\

An engine block with a surface area measured to be 0.90m2 generates a power output of 55 kW with a net engine efficiency of 35%. The engine block operates inside a compartment at 157oC and the average convection heat transfer coefficient of 60 W/m..

  Determine the size of the equipment

Building HVAC Requirements - Indoor Air Quality and Mechanical Ventilation and how determine the size of the equipment if i need for 60cfm.?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd