What is the poisson''s ratio of the block

Assignment Help Mechanical Engineering
Reference no: EM131215809

a block is subjected to a triaxial stress of 16 mpa on the YZ , - 11 mpa on the XZ face & 52 mpa along XY face. if these stresses produce a strain in the x - direction of 49.2 x 10^-6 m/m, what is the poisson's ratio of the block.

Reference no: EM131215809

Questions Cloud

Prepare the end of the period closing entries : Prepare the end of the period closing entries for the Fitness Center - Prepare a post closing trial balance - Prepare a post closing trial balance.
What are the risks and benefits of exploring the problem : What are the risks and benefits of exploring this problem? Who will I need to involve as participants in exploring this problem? How will the possible outcomes of exploring this problem impact the stakeholders positively and/or negati..
Roles and responsibilities of health care management : Write a paper that describes the roles and responsibilities of health care management in addressing this pressing dilemma.
Was there any environmental damage : Were any special technologies or scientific developments used to restore the situation back to normal? If so, explain. Who should be responsible for funding and providing the tools, equipment, and technology-federal, state, or local governments? Wh..
What is the poisson''s ratio of the block : a block is subjected to a triaxial stress of 16 mpa on the YZ , - 11 mpa on the XZ face & 52 mpa along XY face. if these stresses produce a strain in the x - direction of 49.2 x 10^-6 m/m, what is the poisson's ratio of the block.
Who will be responsible for financing and payment of invoice : What kinds of communications technology will private intelligence collectors and analysts use to communicate with the other fusion center stakeholders? Explain. Would they have access to secure federal channels or networks? Why or why not?
Proposal for an erp system : "Response to Request - For - Proposal (RFP) for an ERP System". Aim: This team based assignment is designed to give you the opportunity to learn about ERP systems and to make decisions based on your investigation
Discuss the rationale for a dissemination plan : Discuss the rationale for a dissemination plan for a research or evidence-based project.- how important is the knowledge of the research process to you in your continued practice of nursing?
What were the most compelling topics learned in this course : How did participating in discussions help your understanding of the subject matter? Is anything still unclear that could be clarified? What approaches could have yielded additional valuable information?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Tooling design for composite manufacturing

Write a term paper on Tooling design for composite manufacturing - how tooling is designed for different applications to make composite airplane parts and such.

  Mass of beam is 900 lbm and gravity is 32174 fts2 what is

you have a 32 foot beam that is laying on two pointsone ateach end a and b. mass of beam is 900 lbm and gravity is

  Gauge pressure at the oil-water interface

A barrel contains a 0.120-m layer of oil floating on water that is 0.250 m deep. The density of the oil is 600 kg/m.

  Heat exchanger required to achieve the desired heating

A counter-flow double pipe heat exchanger is heat water from 20 degrees Celsius to 80 degrees Celsius at the rate of 1.2 kg/s. The heating is to be accomplished by geothermal water available at 160 degrees Celsius at a mass flow rate of 2 kg/s.

  Calculate the required heat transfer areas

Assuming an overall heat transfer coefficient of 2000 W/m2 · K, calculate the required heat transfer areas for the following exchanger configurations:

  Calculate the maximum pressure that the reactor is likely

a gas mixture containing 85mole methane and the balance oxygen is to be charged into an evacuated well-insulated

  Thermal efficiency of the cycle and mean effective pressure

A gasoline engine is modeled as an Otto cycle. It has at temperature and pressure at the beginning of compression of 10°C and 90 kPa. The compression ratio is 7 and the specific energy added to the air during the heat addition process is 1432.46 kJ/k..

  Heat transfer coefficients for free convection

Estimate average values of the fin heat transfer coefficients for free convection (hc) and radiation exchange (hr). Use these values to predict the tip temperature and fin effectiveness.

  Determine the heat rate entering the tube

If  the  tube  surface  temperature  at  the  exit  is Ts,o 160°C, determine the heat rate entering  the tube. Evaluate properties at T 400 K.

  Determine the air velocity

A Pitot-static probe connected to a water manometer is used to measure the velocity of air. If the deflection (the vertical distance between the fluid levels in the two arms) is 7.3 cm, determine the air velocity. Take the density of air to be 1.2..

  Discuss johnson & johnson''s approach on providing an it

Needing a writing help with a 3-4 page paper on the Case Study 6-2 Johnson & Johnson's Enterprise Architecture, this is from Managing and Using Information Systems by Pearson & Saunders.

  Determine the rotor diameter and the nozzle angle if the

an inward radial flow turbine is to develop 400 hp when supplied with air at 800c and 3 bar abs the exhaust total

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd