What is the outage probability p

Assignment Help Electrical Engineering
Reference no: EM13275898

Problem 1:

The received signal energy E is uniformly distributed in between [0 10] . Let the mean of E is 5.

a) Consider a particular communication system that the threshold is 1.5. If the signal energy falls below the threshold, the system is in the outage state. What is the outage probability P?

b) If there are two diversity branches (E1 and E2) and pure selection is the diversity selection algorithm what is the outage probability if El= E2? (assume the outage probability of one branch is P, you don't have to know the right answer of part a)

c) If there are two diversity branches (E1 and E2) and pure selection is the diversity selection algorithm what is the outage probability if E1=10-E2? (assume the outage probability of one branch is P. you don't have to know the right answer of pan a)

Problem 2.

A white noise x(t) appears at the input of a transmitter (the power is turned on). Let the transmitter frequency response be Hr(o ). the channel frequency response be Hc(o) and the receiver frequency response be 1-1,(6)). What is the autocorrelation of the receiver output?

Problem 3

The received signal

r = hd + pp

where h is the channel response. d is the data and n is the noise. If the channel response h is known to the receiver. use the MMSE approach to estimate data d. Show all detailed steps of derivation.


Attachment:- Assignment--22.docx

Reference no: EM13275898

Questions Cloud

Which system ratio of bit energy to one-sided noise density : Assume a binary PCM system in which the system ratio of the bit energy to the one-sided noise density at the receiver input is 10 dB. Assume that the probability of error for any value of the independent variable off the scale can be approximated ..
A raman spectrum is consistent with a trigonal-bipyramidal : Detailed analysis of the 369 and 295 cm-1 bands show them to arise from totally symmetric modes. Show that the Raman spectrum is consistent with a trigonal-bipyramidal geometry.
Determine required sampling rate and min required bandwidth : Consider a PCM-TDM system in which 24 signals are to be processed. Each signal has a baseband bandwidth of 3 KHz. The sampling rate has to be 33.3% higher than the theoretical minimum, and 8 bits are to be used.
Explain the symmetry elements of objects : Determine the symmetry elements of objects with the same shape as the boundary surface of a) an s orbital, b) a p orbital c) a dxy orbital d)a dz2 orbital.
What is the outage probability p : Consider a particular communication system that the threshold is 1.5. If the signal energy falls below the threshold, the system is in the outage state. What is the outage probability P?
What is the lower confidence limit test results : If the PEL, PERSONAL EXPOSURE LIMIT for a substance is 500 ppm., the SAE is 0.10 for the sampling method, what is the lower confidence limit test results
Explain how many planes of symmetry does a benzene molecule : How many planes of symmetry does a benzene molecule possess? What chloro-substituted benzene of formula C6HnCl6-n has exactly four planes of symmetry
Determine the height from which the ball was thrown : A ball is tossed from an upper-story window of a building. The ball is given an initial velocity of 8.60 m/s at an angle of 25.0° below the horizontal. Find the height from which the ball was thrown
Determine the approximate received power level required : in a binary DPSK receiver, determine the approximate received power level (in fW) required for a probability of error of 10-6 based on a data rate of 1 Mbit/s, an antenna temperature of 100 K, and a receiver temperature referred to the input of 15..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the snr in output of each systems in db

A voice frequency massage signal (fmax=B= 4 kHz) is transmitted by three binary systems: PCM (μ = 255), DPCM (α = 10), and DM. The bit rate required is Rb = 120 kbps, and m_p2/(m2 (t))= 2  a) Determine the SNR in output of each systems in dB.

  Draw the state diagram for the 2-bit down-counter

Using your knowledge of ‘State Machine' design from logic design principles, draw the state diagram for the 2-bit down-counter, generate the state transition table, the flip-flip input equations for D Flip Flop, and finally the logic diagram of th..

  Explain which parameter of an fm transmission determines

Do either or both of the reasons you gave in part (a) above also apply to a point to point voice link using frequency modulation? c. Which parameter of an FM transmission determines whether it is wideband or narrow band?

  Determine whether the given signals are periodic

Determine whether the following signals are periodic. If they are, find the smallest periods (fundamental periods). a) f(x,y) = sin (2 pi x) cos(4 pi y) b) Discrete signal: f(m,n) = sin ( pi * m / 5) cos(pi * n / 5)

  What is the equivalent of resistors connected in parallel

What is the equivalent (total) resistance of 100, 200, and 50 resistors connected in series What is the equivalent (total) resistance of 100, 200, and 50 resistors connected in parallel

  Find the total power delivered by the dc voltage source

The power is generated by a DC power facility at a voltage of 10 V and deliver by two power lines with resistance Rline=3 ohm. The maximum power the voltage source can deliver is 5 W. a) Find the total power delivered by this DC voltage source

  What is the maximum load current that can be supplied

Two parallel connected 10 kV to 120 V 60 Hz single phase transformers supply a varying load. Assuming 0.85 PF, what is the maximum load current that can be supplied by this parallel combination of transformers wihout overloading either of them

  Determine the irradiance of the filament

A coiled tungsten wire of diameter 50um and length 10cm is glowing at a temperature of 2000°C within an evacuated light bulb. Determine the irradiance of the filament and the fraction of irradiance within the visible range of wavelength.

  Explain what will the new mean and variance

Maximum Likelihood to get the above parameters i.e. u0 and var. Now from these 999 points, I take one point out (lets call it i) and add a new point (lets call it j). What will the new mean and variance be?

  Find the expression for current entering the upper terminal

a current entering the upper terminal of an ideal basic circuit is i= 20cos 5000t A. Assume the charge at the upper terminal is zero at the instant the current is passing through it maximum value. Find the expression for q(t).

  Determine the value using a butterworth filter

A vibration trandsucer measures a sinusoidal signal with up to a 100-hz frequency and an amplitude of + and - 5 v. Superimposed on this signal is an additional signal with a freq of 1000 hz. and amplitude of .2

  Find relation between acceleration in m-s2 nd output voltage

An LVDT is used in an accelerometer to measure seismic-mass displacement. The LvDT and signal-conditioning output is 0.31 mV/mm with a +/-2 cm maximum core displacement.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd