What is the nozzle-exit-to-throat area ratio

Assignment Help Mechanical Engineering
Reference no: EM13217511

The hot gas supply to a propulsion nozzle is at a pressure of 55 kPa and a temperature of 800 K.

The ambient pressure is 15 kPa. If the ratio of specific heats is 1.33, approximately constant, and the molecular weight of the mixture is 30, determine the ratio of gross thrusts for two cases:

a. The nozzle is converging-diverging with the area ratio for correct expansion to ambient pressure.

b. The nozzle is converging only.

What is the nozzle-exit-to-throat area ratio for case (a)? The gross thrust is the contribution to engine thrust made by the exhaust nozzle only.

 

Reference no: EM13217511

Previous Q& A

  Value of the capital portion of the debenture

The fair rate of return on similar debentures is 14% before tax. Calculate the present value of the capital portion of the debenture.

  Find the height of center of mass

find the best fit Gaussian Curve through the data and plot the data and curve on the same graph.

  Define corporation is managed by the federal government

Which of the following is TRUE regarding a corporation? a. it is authorized by statute b. it is managed by the federal government

  History from the presidency of andrew johnson

This course has covered American history from the presidency of Andrew Johnson to George W. Bush. In this period, 26 men served as president. In an essay of 500-600 words, which president do you think left the boldest mark on American History?

  Determine the preassure at the bottom of the gate

A square 3m x 3m gate is located in the 45* sloping side of a dam. Some measurements indicate that the resultant force of the water on the gate is 500kN.(a)Determine the preassure at the bottom of the gate.(b)Show on a sketch where this force acts..

  Poor memory illustrates

Mrs. McBride can't consciously recall how frequently she criticizes her children because it would be too anxiety-arousing to do so. Sigmund Freud wuold have suggested that her poor memory illustrates:

  What is the use of dimentionsless numbers

what is the use of dimentionsless numbers, and why the temperature is max on gas turbine blade tip.

  Find the value of the gain

Using MATLAB Simulink, set up the negative feedback system of and find the value of the gain

  Compute the assurance of learning exercise

Complete the Assurance of Learning Exercise. You will be asked to analyze and to compare and contrast the code of ethics of both Starbuck's and McDonald's. Summarize your analysis and findings

  Find the mass in both a and b

The piston is now unlocked so it is free to move, and it conducts heat so the air comes to a uniform temperature . Find the mass in both A and B, and the final T and P.

Reviews

Write a Review

 

Similar Q& A

  What is the formation volume factor of the oil

The separator produces 43,150 scf/d of 0.724 gravity gas, and the stock tank vents 7240 scf/d of 1.333 gravity gas. What is the formation volume factor of the oil? What is the solution gas-oil ratio? Which of the previous answers applies only at t..

  What is the new quality and volume

Water at 200KPa with a quality of 25%has it temperature raised to 20degrees celcius in a constant pressure process. What is the new quality and volume?

  Create a design of rankine cycle

your job is to create a design of Rankine cycle that create the most possible power from this heat source . you may use any working fluid for which you can find the properties , assume the turbines 92% efficient and pumps 85%

  Product and engineering design review

Product and Engineering Design Review

  Evaluate the reduction in pump bhp

Evaluate the reduction in pump BHP required by heating the oil from 50° F to 100° F. Suppose efficiency of 80% (HP)

  Determine the angular acceleration of the bars ab and bc

collar c moves along a circular guide with radius R=2ft with a constant speed v=18ft/s. at the instant, the bars AB and BC are vertical and horizontal respectively. Letting L=4ft and H=5ft, determine the angular acceleration of the bars AB and BC ..

  What of diameter of steel rod is required to support tension

What of diameter of steel rod is required to support a tension load of 44.5kn?assume that the allowable stress for the steel is F=165n/mm.

  Determine the magnitude and direction

The direction of the forces are 0,-30 and +120 degrees from the positive X axis. Determine the magnitude and direction of the resultant force.

  Compare to the actual performance

Get information about a car engine .drive the ideal performance using the appropriate cycle and compare to the actual performance.

  Determine the maximum contact pressure

The wheel of a crane lift is rolling on a flat rail. The radius of the wheel is 4 in, the contact length and force are 2.5 in and 1 ton respectively, and E = 30 MPa and ν = 0.3 for both parts. Determine (a) the maximum contact pressure, (b) the wi..

  Determine the speed at which it strikes the ground at b

the snowmobile is traveling at 10m/s when it leaves the embankment at A.determine the speed at which it strikes the ground at B and its maximum acceleration along the trajectory AB.

  How did you do the maintenance during your workshop

Show how did you do the maintenance during your workshop

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd