What is the net torque about the center of the pulley

Assignment Help Mechanical Engineering
Reference no: EM131110763

From her elevated DJ booth at a dance club, Caroline is lowering a 2-kg speaker using a 0.6-kg disk of radius 8 cm as a pulley (Figure). The speaker wire runs straight up from the speaker, over the pulley, and then horizontally across the table. She attaches the wire to the 4-kg amplifier on her tabletop, and then turns to get the other speaker. The table, however, is nearly frictionless, and the whole system begins to move when she lets go.

1622_Pulley.jpg

(a) What is the net torque about the center of the pulley?

(b) What is the total angular momentum of the system 3.5 s after release?

(c) What is the angular momentum of the pulley at this time?

(d) What is the ratio of the angular momentum of each piece of equipment to the angular momentum of the pulley?

Reference no: EM131110763

Questions Cloud

Wabaunsee corporation uses the direct method : Wabaunsee allocated one-third of its depreciation expense to selling expenses and the remainder to general and administrative expenses.
Find the vertical velocity of the package for t = 8.0 min : Find the vertical velocity of the package for t = 8.0 min.
The fluidity of membranes : 1) Apparently the fluidity of membranes is important to their biological functions. It was shown that in E. coli the ratio of saturated to unsaturated fatty acids decreases as the temperature decreases. How does the presence of unsaturated fatty acid..
What is your null hypothesis and alternate hypothesis : What is your null hypothesis? Alternate hypothesis? Is this a one-tailed or two-tailed hypothesis and why? What is the criterion z? Can you check this question?
What is the net torque about the center of the pulley : What is the net torque about the center of the pulley? What is the total angular momentum of the system 3.5 s after release? What is the angular momentum of the pulley at this time?
Evaluate her 2012 financial performance : During the year, Ms. Chen paid interest of $15,000 on the $120,000 borrowed to start the business. She paid an average tax rate of 30% during 2012. Prepare an income statement for Cathy Chen, CPA, for the year ended December 31, 2012. Evaluate her 20..
Identify the crime scenes involved : On the basis of the facts provided, identify the crime scene(s) involved. Outline the steps a forensic technician should take to process the scene.
Where is the radius vector from p to any point on s : et be a smooth parametric surface and let P be a point such that each line that starts at P intersects S at most once. Where is the radius vector from P to any point on S, r = |r|, and the unit normal vector is directed away from P.
Briefly discuss the form and informational content of each : The income statement for the year ended December 31, 2012, the balance sheets for December 31, 2012 and 2011, and the statement of retained earnings for the year ended December 31, 2012, for Technica, Inc., are given below and on the following page. ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd