What is the net heat flux from the surface when solar

Assignment Help Mechanical Engineering
Reference no: EM13640917

In space ships, heat rejection to the surroundings is by radiation. A radiator in a space ship has an absorptivity α of 0.1 for 0 < λ < 2 μm, and 0.95 for λ > 2 μm. The surface is maintained at 600 K. What is the net heat flux from the surface when solar irradiation on the surface is 1200 W/m2? Assume a sky temperature of 0 K and that the surface is diffuse.

Reference no: EM13640917

Questions Cloud

How will increasing the sample size without changing the : how will increasing the sample size without changing the level of confidence affect the width of a confidence interval
A student carefully diluted 250 ml of 6 m naoh solutionin : a student carefully diluted 25.0 ml of 6 m naoh solutionin 475 ml if distilled water. calculate the molarity of the
Determine the linear acceleration of the boxes assuming : boxes are sitting on a conveyor belt as the conveyor is turned on moving the boxes toward the right. the belt reaches
To bring the solution to a ph of 735 how much 0100 m koh : phosphoric acid is a commonly used biological buffer because the pka for dissociation of its second proton is near
What is the net heat flux from the surface when solar : in space ships heat rejection to the surroundings is by radiation. a radiator in a space ship has an absorptivity alpha
Suppose that the proportion of fatal single-car accidents : suppose that the proportion of fatal single-car accidents that involve alcohol consumption on the part of the drive is
What is the probability that the space vehicle will have a : a what is the probability that the space vehicle will have a successful launch?b given that the space vehicle had a
How much higher or lower is the launch point relative to : a projectile is fired with an initial speed of 34.0 ms at an angle of 35.0circ above the horizontal. the object hits
Point b is 10 m above point a and the pressure at b must be : water at 40 degrees celsius flows from a to b through a 300-mm cast iron pipe xi0.000061 m 250 m long. point b is 10 m

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the shape of isopycanal surface between 400 and

surface geostrophic velocity 0.5 ms density 1026kgm3 gravity 9.8ms ring radius 50km. you take velocity measurment

  A house has a composite wall of plaster board lp 10mm k072

a house has a composite wall of plaster board lp 10mm k0.72 wm.k fibre glass insulation lb100mm k1.4 wm.k and plywood

  Calculate the quality of the system

calculate the quality of the system to begin with. calculate the amount of liquid water to begin with. calculate the heat transfer during the heating process.

  Determine the amount of money this facility will save a

during a plant visit it was noticed that a 12-m-long section of a 12-cm-diameter steam pipe is completely exposed to

  A cast-iron cylinder of 300mm bore carries a pressure of

a cast-iron cylinder of 300mm bore carries a pressure of 30 newtons per squaremillimetre what should be its thickness

  Find the heat transfer and work per unit mass of air in

consider an air-standard otto cycle and a modified cycle in which the isentropic compression and expansion processes

  A length sufficient to accelerate a 2mm diameter projectile

a linear motor is built utilizing neodymium permanent magnets supplying a magnetic field of .75t rails with an average

  After a few minutes it is observed that the bit is hot

a hand drill is used to drill a holbein a very hard material. because the bit is very dull it spins with out advancing.

  Weight are removed so that the gas expands according to the

the cylinder-piston arrangement contains carbon dioxide at 300kpa and 200 degrees celsius and the volume 0.2m3. weight

  The temperature is assumed to vary linearly as a function

a bicyclist leaves from her home at 9 a.m. and rides to a beach 40 mi away. because of a breeze off the ocean the

  Determine the heat transfer for this process

during this process heat is exchanged with surrounding such that the entire air remains at 30 degree celsius at all times.determine the heat transfer for this process.

  Find the reversible amount of work per unit mass find the

the air with constant properties in a steady adiabatic flow enters a system at a pressure of 10 bars and 500 k with a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd