User Account

All Pages

What is the modulus of resilience

Assignment Help Mechanical Engineering
Reference no: EM13216868

Labratory measurements show that when a certain material has a grain diameter of 2.33x10-2 mm it's yield strength is 107 MPa. When the material's grain diameter decreases to 1.84x10-2 mm it's yield strength increases to 117 MPa.

When the average grain diameter is increased to 3.20x10-2 mm, what is the modulus of resilience (in J/m^3) if the modulus of elasticity is known to be 134 GPa?

 

Reference no: EM13216868

Questions Cloud

Determine the minimum required wire diameter : a large tower is to be supported by a series of steel wires.it is estimated that the load on each wire will be 11100N. determine the minimum required wire diameter assuming a factor of safety of 2 and a yield strength of 1030MPa.
Why did the united states use atomic weapons against japan : "Why did the United States use atomic weapons against Japan? Do you believe President Truman made the right decision?
Determine the magnitude and direction of the resultant : The boom OA carries a load P and is supported by two cables as shown. Knowing that the tension is 510 N in cable AB and 765 N in cable AC, determine the magnitude and direction of the resultant of the forces exerted at A by the two cables.
Explain how companies attempt to compensate their employees : Identify different compensation systems and provide the benefits and disadvantages of each. Define Comparable Worth and explain how companies attempt to compensate their employees based on such a concept and not violate any federal legislation.
What is the modulus of resilience : When the average grain diameter is increased to 3.20x10-2 mm, what is the modulus of resilience (in J/m^3) if the modulus of elasticity is known to be 134 GPa?
Federal agent vs. a state or local law enforcement officer : Discuss the difference of the role of the federal agent vs. a state or local law enforcement officer. What is the source of federal law as opposed to state/local law? Identify and explain the role of the U.S. Attorney in the federal criminal process ..
What must be its minimum yield strength : A steel alloy to be used for a spring application must have a modulus of resilience of at least 2.07 MPa (300 psi). What must be its minimum yield strength?
Compute the work done for this process : (1) I shte cooling process polytropic? If so, what is the value of n? (2) Find the final state pressure. (3) Compute the work done for this process considering the water as a closed system.
Determine the height to which the pulley is lifted : a simple pulley with the given radius r used to lift heavy objects is positioned 10 feet above ground level. Given that the pulley rotates theta degrees, determine the height to which the pulley is lifted.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the speed at which it strikes the ground at b

the snowmobile is traveling at 10m/s when it leaves the embankment at A.determine the speed at which it strikes the ground at B and its maximum acceleration along the trajectory AB.

  Capabilities of solidworks motion manager

Prepare a power point presentation and a short report relating to the capabilities of Solidworks Motion Manager.

  Use of waste heat and renewable heat sources

Energy in the home, personal energy use and home energy efficiency and Efficient use of ‘waste' heat and renewable heat sources

  Determine temperature at which the water starts boiling

A cooking pan whose inner diameter is 20 cm is filled with water and covered with a 4-kg lid. If the local atmospheric pressure is 101 kPa, determine the temperature at which the water starts boiling when it is heated.

  Determine the compression ratio

determine (a) the compression ratio, (b) the cycle efficiency, (c) exhaust temperature, and (d) mean effective pressure (kPa). Draw (e) a P-v diagram and (f) a T-s diagram

  Plot data using appropriate dimensionless groups

Assume that viscous effects are negligible Plot this data using appropriate dimensionless groups

  Minimum weight design of a variable shape three-bar truss

Obtain a new solution, and determine whether any buckling constraints are active. If no buckling constraints are active for L = 10 in., re-run the analysis by increasing L , and estimate the value of L at which at least one buckling constraint b..

  What are the angles

solution of oblique-angled triangle all threesides known two side at 7.5 in. and base at .3437 in. what are the angles ?

  Determine the acceleration of the car

A motorist enters a freeway at 36 kph and accelerates uniformly to 90 kph. From the odometer in the car, the motorist knows that she traveled 0.20 km while accelerating. Determine a.) the acceleration of the car, b.) the time required to reach 90 ..

  Explain finding metal removal rate

Finding Metal Removal Rate In an electrochemical machining operation, the frontal working area of the electrode is 2.5in squared

  Determine the temperature at which the treatment was carried

If after 49.5 h the concentration of carbon is 0.35 wt% at a position 4.0 mm below the surface, determine the temperature at which the treatment was carried out.

  Determine the angular velocity and angular acceleration

Block B of the mechanism is confined to move within the slot member CD. If AB is rotating at a constant rate of AB = 3rad/s, determine the angular velocity and angular acceleration of member CD at the instant shown.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd