What is the maximum error of the linearly marked

Assignment Help Mechanical Engineering
Reference no: EM13623194

The specific volume of mercury is given by the equation:

V(T) = V(0 degree C)x(1+1.82x10^-4T + 7.8x10^-9T), T in degree C

Suppose that you take an unlabeled mercury in glass thermometer, mark .01 degree C and 100 Degree C for the triple point and normal boiling point of water, and then place intermediate temperature points by linear interpolation. Because of the non-linear expansion of mercury, your temperature scale will differ a little from the true Celsius scale. What is the maximum error of the linearly marked thermometer? What other source of error do you need to consider if you are interested in constructing very accurate thermometers?

Reference no: EM13623194

Questions Cloud

When a 100ohm resistor is connected to a battery of emf e : when a 100ohm resistor is connected to a battery of emf e and internal resistance of r the battery delivers a power of
The arguement of the sine are in radians and t is in : a particle is moving along a circular path having a radius of 5.7 in. such that its position as a function of time is
A 40x10-6 farad capacitor is connected in series with a : a 4.0x10-6 farad capacitor is connected in series with a 2000 ohm resistor across a 20v-dc power supply and an open
An eye care health clinic experiences 15 customers arrive : an eye care health clinic experiences 15 customers arrive every 60 minutes between 1200-100 mid day. there are three
What is the maximum error of the linearly marked : the specific volume of mercury is given by the equationvt v0 degree cx11.82x10-4t 7.8x10-9t t in degree csuppose that
In a standard normal distribution what must z be such that : in a standard normal distribution what must z be such that p-zlt z lt z
Determine the transverse component of the pegs acceleration : peg p is driven by the fork link oa along the curved path described by r etheta m. when theta pi 4 rad the angular
Ferrari a leading manufacturer of formula one race cars : ferrari a leading manufacturer of formula one race cars claims that the average acceleration time to go from zero to
You estimate that the value of a single family home is : you estimate that the value of a single family home is 700000. however local zoning regulations would permit a 5 unit

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the velocity and rate of flow of the metal

What is the velocity and rate of flow of the metal into the mold? Is the flow turbulent or laminar? (Pure aluminum density ρ = 2.7 g/cm3).

  Samples2 i want a unique version of this

i want a unique version of this

  Water pressure of 10 kpa is pumped to a pressure of 4mpa

water pressure of 10 kpa is pumped to a pressure of 4mpa. what is minimum energy requirement of the pump in kjkg.

  The turbine exhausts to atmospheric pressure if both the

a gas turbine takes in 250000 lbmhr of air at 80f and compresses it to 6 atmospheres. the combustion of gas adds

  The diameter at the point of fracture is 658 mm and the

a cylindrical metal specimen having an original diameter of 11.05 mm and gauge length of 51.7 mm is pulled in tension

  Is there an economic case for renewable energy

Is there an economic case for renewable energy? This issue was recently a "hot topic" in the news, and you are referred to the following newspaper article for a representation from the media.

  Determine the volume after all the ice is melted

100 kg of liquid water at 25C and 50 kg of ice at 0C are placed in an isolated container. (a) (b) (c) Find the initial volume of the liquid-ice mixture, in m3. Determine the volume after all the ice is melted, in m3. Will the temperature of the li..

  Determine the temperatures of surface 1 through 4 of the

determine the temperatures of surface 1 through 4 of the furnace cavity of example 13.3 if the entire furnace

  When it is initially filled with gas at 100 deg c what is

a small steel cylinder is used as a pressure vessel for a paint gun. the label says 24 grams co2 filled. assume the

  What is the design objective

2. What is the design objective? -to minimize the required power input to the compressors 3. What parameters does the design engineer control?

  List and explain three process parameters

h injection molding was portions of the part not filling. List and explain three process parameters that may aid in the correction of this error. What other errors might adjustments in these parameters help allay?

  A 200-kg 5-m-wide rectangular gate shown innbspthe figure

a 200-kg 5-m-wide rectangular gate shown innbspthe figure is hinged at b and leans against thenbspfloor at a making an

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd