What is the maximum ac peak to peak voltage input

Assignment Help Electrical Engineering
Reference no: EM13228141

The LM358 op amp can be a single or dual supply op-amp. This mean that it can operate with just a single supply i.e. + 5 volt or with dual supplies i.e. (+ and -) 5 volt supplies. With a non-inverting configuration with dual supplies (+5v and -5v) being supplied to the LM358 Please answer the following questions.

1. What is the gain formula for a non inverting op amp?

2. With this configuration, is there a maximum output voltage peak to peak, if so what would it be?

3. This op amp is configured for a gain of 11. Input signal is an AC sine wave signal. What is the maximum AC peak to peak voltage input?

4. What happens to your output signal when the input signal is above the maximum peak to peak input voltage?

Reference no: EM13228141

Questions Cloud

Explain concentration is required to precipitate : If the concentration of Mg2+ ion in seawater is 1350 mg/L, what OH- concentration is required to precipitate Mg(OH)2
Compute the concentrations of the nonionized acid : Calculate the concentrations of the nonionized acid (HA) and of the ions of a 0.100 M formic acid (HCO2H) solution at equilibrium, and calculate % ionization.
Compute the work in joules when water vaporizes : Calculate the work in Joules when 2.5 mols of water vaporizes at 1 atmosphere pressure and 25 degrees C. The work is done in pushing back the atmosphere.
What is the probability of three of a kind for a poker hand : 1. Compute the probability of having the sum of 10 by throwing (a) two dice, (b) three dice. 2. What is the probability of three of a kind for a poker hand with (a) a card deck of 52 cards, (b) a card deck of 32 cards by removing all cards of numb..
What is the maximum ac peak to peak voltage input : The LM358 op amp can be a single or dual supply op-amp. This mean that it can operate with just a single supply i.e. + 5 volt or with dual supplies i.e. (+ and -) 5 volt supplies. With a non-inverting configuration with dual supplies (+5v and -5v)..
Explain chemical reaction and pushes back the atmosphere : Xenon gas is released during a certain chemical reaction and pushes back the atmosphere with a change in volume of the vessel (it has a movable piston) from 2 to 20 Liters. Calculate the work done by this release of gas.
Calculate the range of frame sequence numbers : A selective-repeat (SR) data link layer protocol uses 4 sequence bits to number it's frames. The source, C starts from frame 0 and proceeds following the Sr protocol. Let us start analyzing the frame/ACK transmissions when the first outstanding fr..
What factors would you consider in your audit : Describe how you would conduct a bi-cultural audit of two organizations considering a merger. What factors would you consider in your audit? Who would you talk to? What techniques would you use?
Explain according to increasing change of entropy values : Arrange the following reactions according to increasing change of entropy values. A. CH4(g) + H2O (g) = CO(g) + 3H2(g) B. C(s) + O2(g) = CO2 (g) C. H2O2(liquid) = H2O(liquid) + 1/2 O2 (g)

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the voltage gain realized

A transconductance amplifier with Ri = 2 kΩ, Gm = 40 mA/V , and Ro = 20kΩ is fed with a voltage source having a source resistance of 2kΩ and is loaded with a 1kΩ resistance. Find the voltage gain realized (from the source internal voltage to the o..

  Find minimum pos with inversion and de morgans laws

c) Write the SOP boolean equations as obtained directly from the partial truth table above and sketch a logic circuit diagram for them. d) Reduce the above equations step-by-step into the simplest form that would use only NAND gates.

  Determine the dc self bias line expression relating id to vg

a) By applying Kirchoff's voltage law to the output (DC) circuit loop determine the DC Load Line, i.e. an expression relating Id to Vds. Comment briefly on the significance on the result, with respect to the slope and x-axis intercept.

  Find the current nd voltage to obtain desired optical output

calculate the extraction efficiency and find the current and voltage needed to obtain the desired optical output. Once you know the current density choose Area and Find Vf that will give you the desired current density and current (If= Jf x A= Jn ..

  Calculate the numerical value of the mutual capacitance

Calculate the numerical value of the mutual capacitance of a square parallel plate capacitor whose dimensions are 1 mm X 1 mm if the two plates are separated by a distance of 2 mm. The relative dielectric constant of the material between the two p..

  What is speedup in throughput for each of these improvements

Increasing the number of SIMD processors to 15 (assume this change doesn't affect any other performance metrics and that the code scales to the additional processors)

  What is the total volume of silica

A silica fiber has an outer diameter of 125 micro meter. What is the total volume of silica for a 1-km length? This fiber is wound on a spool whose unloaded diameter is 20 em. The spool height is 10 em. Compute the diameter of the fully loaded spo..

  At what frequency is impedance a minimum

A series-resonant RLC circuit has R = 80 (ohms), L=25mh, and C=10pF. A) Sketch and label the circuit. B) Find fo, the resonant frequency. C) At what frequency is impedance a minimum D) What is the magnitude of the impedance at this frequency

  Examine of link budget dth qpsk satellite link

Analysis of link budget DTH QPSK Satellite link, A direct-to-home satellite television system uses a geostationary satellite in orbit above the equator at a longitude of 109 degrees west.

  Explain magnitude bode plot for any given transfer function

Magnitude bode plot for any given transfer function Can some one teach me an easy way to make a bode plot for any given transfer function magnitude only (not phase).

  What is the group delay between a pulsar pulse received

A pulsar lies 1000 light years from Earth. The average plasma concentration is 1 el/cc. Using the plasma dispersion relationship for group speed, what is the group delay between a pulsar pulse received at 1 GHz and at 800 MHz

  What is the net number of electrons per second

What is the net number of electrons per second that pass through the cross-section of a wire carrying 5 A of dc current The current now is due to electrons, and the magnitude of the charge of each electron is 1.60×10?19 C.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd