What is the matched filter for this waveform

Assignment Help Mechanical Engineering
Reference no: EM131349986

A partial-response waveform can be designed by using any Nyquist pulse in place of the sinc pulse.

a. What is the equivalent channel for a duobinary partial-response waveform based on the Nyquist pulse

48_e28a558d-5e2e-4390-a146-86fa269cf6d1.png

and the generator polynomial g(x) = x + 1?

b. What is the matched filter for this waveform? Sketch a decision-feedback demodulator. Sketch an alternative implementation that uses a precoder.

Reference no: EM131349986

Questions Cloud

What is the purpose of inpatient and outpatient facilities : What are the main differences between inpatient and outpatient facilities? What is the purpose and importance of both? Why would one type be used instead of the other?
Give a description of the diet and the restrictions : Identify a current fad diet. Give a description of the diet and the restrictions, etc. Provide two days of meal plans
Describe a duobinary system with a four-level input alphabet : Describe a duobinary system with a four-level input alphabet. Give a decision-feedback demodulator including the detection rule.
Compute the composite rating for each location : The critical factors, their weights, and the ratings for each location are shown in the following table. High scores represent favorable values - Compute the composite (weighted average) rating for each location and which site would you choose?
What is the matched filter for this waveform : What is the matched filter for this waveform? Sketch a decision-feedback demodulator. Sketch an alternative implementation that uses a precoder.
Who controls the purse strings and why : How will the price fluctuate? What economic trends are to be observed? Who will make money from the technology? Who is funding the research and development? Who controls the purse strings, and why?
Conduct a stakeholder analysis : Examine Box 3.0 - Conducting a Stakeholder Analysis. Choose one (1) policy issue in the U.S. and generate a list of at least five (5) stakeholders who affect or are affected by problems in the issue area. Next, apply the procedures for a stakehold..
Identifies the purpose of the evaluation : A 2- to 3-page draft of the program evaluation plan to submit to the stakeholders that: Identifies the purpose of the evaluation. Describes the questions that will be addressed and the type of information that will be collected
Discuss about the models and structuring : Review Question 6 and select one of the ill-structured problems taken from the journal Policy Analysis (now the Journal of Policy Analysis and Management Under the title "Department of Unintended Consequences". Analyze the problem; then, provide a..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the air temperature at the limiting pressure

a cubic tank 1m3 is filled with air at 280k and 100 kpa. it is fitted with a relief valve that will vent at 600 kpa.

  Explain why these techniques are effective

What welding techniques can be used to avoid loss of strength in the material in the heat-affected zone? Explain why these techniques are effective.

  Design cycle time is the cycle time at which you design

Develop a detailed step-by-step sequence of operations for each process or piece of equipment. Calculate the time required for each cut or step in the process. This document is required to determine if the operation can produce parts at the requ..

  Compare annual profit when the plant is operating at 90 of

a planet operation has fixed costs of 2000000 per year and its output capacity is 100000 electrical appliances per

  The pressure at the discharge is 5 psi gage the solution

a 20 degc brix sucrose solution at 70 degf is being pumped from a large open tank at a rate of 16 gallonsmin through a

  Determine the mass flow rate of air

Air enters a nozzle steadily at 50 psia, 160°F, and 155 ft/s and leaves at 14.7 psia and 900 ft/s. The heat transfer from the nozzle to surrounding air is estimated to be 6.0 Btu/lb of air flowing. The inlet area of the nozzle is 0.15 ft2. Based on ..

  Car a is speeding in the positive x direction and is about

car a is speeding in the positive x direction and is about to run through a red light and collide with car b heading

  Refrigerant-134a enters the evaporator coils placed at the

refrigerant-134a enters the evaporator coils placed at the back of the freezer section of a household refrigerator at

  Write the stress tensors at points aand b

Write the stress tensors at points Aand B, both of which are on the top (z-facing surface) of the wrench. Hint: you will need to use some results from Chapter 5.

  What is the temperature at the firebrick-kaolin interface

a furnace wall is composed of three layers 15 cm of firebrick k 1.5 wmk followed by 22.5 cm of kaolin insulation brick

  Determine the average normal stress in the shank

The long bolt passes through the 4 in. thick plate. If the force in the bolt shank is 50 lb, determine the average normal stress in the shank, the average shear stress along the cylindrical area of the late defined by the section lines a-a, and the a..

  Calculate and plot the response of a system with transfer

calculate and plot the response of a system with transfer function gs100s22s3s25s1 to the input ut10exp-tsin5t assuming

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd