Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A MOSFET is used in a boost-buck converter. The on-state loss is 4.2 W, and the switching loss is 2.8 W. The device is in TO-220 heat-sink package. it is desired to avoid a heat sink, and a parallel connection has been suggested. If a second MOSFET is added in parallel,
what is the loss in each part?
will a heat sink be necessary?
Assume that junction ambient R theta(ja) = 45 K/W
A certain load takes 10kW at 0.5pf lagging when connected to a 230V, 60Hz source. The supply company charges a penalty when the power factor fall below 0.8. What size of capacitor must be used in order to avoid penalty
A single phase 220V system draws a current of 15A at a lagging power factor of 0.8. Calculate the value of a capacitor that can be used to improve the power factor of this system to 0.95 lagging.
Electrical wiring: Potentials of neutral and earth wires, Why is the neutral wire in housing circuits also at zero potential
(a) Determine a unit vector in the direction of Q at P(1, 2, 1) (b) Find the component of Q at P in the direction of PT where T is point (5, 3, -4) (c) Where is Q the same as the unit vector of \(a_{x}+11a_{y}+10a_{z}\)
Calculate the PMOS device with to acheive symmetric propagation delays in an inverter (tPLH = tPHL). Use Wn=450nm Ln =300nm and Lp=300nm and solve for Wp. So I think by some ratio I can find what Wp should be, maybe something like Wn/Ln=Wn/Lp
For the given circuit, determine the function of it I.e. is it OR gate? Or AND gate,.. Show all your answer, also draw the symbol and truth table of it.
A 4800/480 volt, single phase transformer is rated at 75KVA. test results performed for rated power showed the following. short circuit test V=80v, P= 2470W, I= Rated current open circuit test V= 480v, I=4Amp, P=616W
For each of the following waveforms, determine its period, frequncy, and effective value a) 5 V b) 2sin80t-7cos20t+5 V c) 5cos50t+3sin50t V d) 8cos^290t mA
Suppose that a voice signal normally occupies 30 kHz of bandwidth and has a signal-to-noise ratio of 20 dB. Spread-spectrum techniques are used to increase its bandwidth to 2 MHz. (a) What is the signal-to-noise ratio of the spread signal
1. Draw a circuit that can scale the voltage from the range of 0~200 mV to the range of 0 ~ 10V. 2. Draw a circuit that can scale the voltage from the range of -200 mV ~0 V to the range of 0 ~ 10V . 3. Draw a circuit that can scale the voltage from t..
Design an XOR gate using standard CMOS logic and with pass-transisitor logic and determine the number of transistors (NMOS and PMOS) required for each implementation.
Given: The terminal pair of a hidden circuit has an open circuit voltage of 200 V. When a 50 k? resistor is placed across the terminal pair, a potential of 80 volts is observed. Required: Determine the terminal voltage that would result if the 50 k
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd