Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
500W lighting is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7A. What is the inductance of the load connected in parallel with incandesent lights? Assume a voltage of 120v and 60hz.
Two IIR filter coefficients are given below, respectively, IIR system 1: Numerator coefficients: bBP = [0.0201 0.0000 -0.0402 0.0000 0.0201 ]; Denominator coefficients: aBP = [1.0000 -2.1192 2.6952 -1.6924 0.6414 ]; IIR system 2: Numerator coefficien..
What resistance must be connected in series with a heater rated at 150mA with hot resistance of 320 ohm in order to operate it safely from a 117-V source. What power rating must this resistor have
Fundamentals of Electric Circuits fourth edition: alexander, sadiku chapter 12 problem 12.29 A balanced three phase wye-delta system has Van= 120 angle 0 Vrms and Zdelta= 51+ j45 ohms. if the line impedance per phase is 0.4 + j1.2 ohms,
Get digital still images and video sequences from the Internet, as needed. You can use color and/or gray-scale images. 2. Implement intra-frame DPCM . Start with a linear quantizer in the initial implementation.
A permanent magnet DC motor has an armature resistance of 0.45 ohm and when a voltage of 120 V is applied to the motor it reaches a steady-state speed of rotation of 25 rev/s and draws 35 A.
This washing machine would have a fill cycle to one level, a 10 second wash cycle, a 10 second rinse cycle and then drain. Include a start button, low level switch, high level switch, an agitator motor, a fill valve and a drain valve.
Many reactors are sited next to large bodies of water so that they can use the water for cooling. Consider a reactor where the intake water is at 18° C. State regulations limit the temperature of the output water to 30° C so as to not harm aquatic..
The transmission line has an impedance of 600 ohms and is terminated in a load of 600 ohms. The transmitter delivers an average power of 0.1 W to the input of the line.
Assume that in addition to the sine-wave signal you have a dc reference voltage of 1.5 V available. Sketch the output signal waveform.
The total admittance for the following circuit is Hint: YT = G + j[Bc - BL] Siemens; G = 1/R Siemens; Bc = wC Siemens and BL = 1/[wL] Siemens Data: Vin AC = 10 sin 1250t, R = 100, C = 4UF, L = 80 mH
A base stationcellular communicationsystems lossless antenna has a maximum gain of 16 dB (above isotropic) at 1,900 MHz. Assuming the input power to the antenna is 8 watts, what is the maximum radiated power density (in watts/cm^2)
(a) At t = 0, the current flowing in a 0.5-H inductance is 4 A. What constant voltage must be applied to reduce the current to 0 at t = 0.2 s (b) Starting at t = 0, a constant 12-V voltage source is applied to a 2-H inductor.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd